[. . . ] Liquid Crystal Projector
Model name
CP-X950W/E
OPERATING GUIDE
Thank you very much for purchasing this Hitachi Liquid Crystal Projector. After reading this manual, keep it carefully for future reference.
O N LA M P TE AN ST N /O D BY M P IN PU T M U TE
ZO O M
S CU FO
Outline
This Liquid Crystal Projector can display various computer signals and NTSC/PAL/SECAM video signals.
Features
(1) High brightness
A highly efficient optical system with a metal halide lamp ensures high brightness.
(2) High resolution
Three separate high-definition liquid crystal panels are used for the R, G and B signals.
(3) Compact size, light weight for portability (4) RGB output terminal (5) RS232C Communication (6) Mouse emulation (7) Power zoom and power focus functions (8) Complies with VESA DDC1/2B specifications
U EN M
T SE RE
Contents
Page
Before use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
FOR THE CUSTOMERS IN U. K
THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND EUROPE. FOR THE U. K PLEASE REFER TO THE NOTES ON THIS PAGE.
IMPORTANT FOR UNITED KINGDOM WORDING FOR CLASS I EQUIPMENT INSTRUCTION BOOKS AND LABELS
The mains lead on this equipment is supplied with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug. [. . . ] If the polarities are confused, it may cause injury or damage near the unit due to a burst of battery or liquid leakage.
· · · ·
Caution Cautions on use Do not drop the remote control transmitter or apply any shock to it. Do not let the remote control transmitter get wet and do not put it on a wet object. If you are not going to use it for a long time, remove the batteries from the remote control transmitter. If operation of the remote control becomes difficult, replace the batteries.
Caution
Cautions on use of the laser pointer.
·The laser pointer on the remote control unit radiates the laser beam from the laser aperture. ·This laser pointer used asthe laser aperture or radiate the laser beam to other persons Do not stare directly into ·
as the laser emitted is a class II laser and it could damage you vision, etc. The three labels below are caution labels for the laser beam.
AVOIDE EXPOSURELASER RADIATION IS EMITTED FROM THIS APERTURE
LASER APERTURE
CAUTION
LASER RADIATIONDO NOT STARE INTO BEAM WAVE LENGTH:670nm MAX. OUTPUT:1mW
CLASS II LASER PRODUCT
RADIAZIONI LASER NON GUARDARE NEL RAGGIO LUCE APPARECCHIO LASER DI CLASSE 2 RAYONNEMENT LASER MANUFACTURED NE PAS REGARDER DANS LE FAISCEAU APPAREIL August-97 A LASER DE CLASSE 2 LASER-STRAHLUNG NICHT IN DEN STRAHL BLICKEN LASER KLASSE 2MANUFACTURER:A
MADE IN JAPAN
Installation
Example of the projector and screen installation
Determine picture size and projection distance as illustrated below.
View from the top
Screen
View from the side
Lens center
b a
Screen (inch) 40 60 80 100 120 150 200 60 89
a (inch) Minimum Maximum 89 134 179 224 269 336 448
b (inch) 3. 4 5. 1 6. 9 8. 6 10. 3 12. 9 17. 2
a: Distance from the projector to the screen. (±10%) b: Length from the center of the lens to the bottom of the picture. (1024 dots × 768 dots)
119 149 179 224 298
Installation of liquid crystal projector
Please basically use liquid crystal projector at the horizontal position. If you use liquid crystal projector by the lens up position, the lens down position and the side up position, this may cause the heat inside to build up and become the cause of damage.
How to use foot adjusters
Adjust the projection position using the foot adjusters at the bottom of the projector.
View from the front
unlock lock
View from the side
Foot adjuster A viewing angle of 2° ~ 12° can be changed.
1. Caution Do not unlock the foot adjusters while you do not support the projector, to avoid falling of the projector and causing an injury. Do not revolve the foot adjusters by force, the foot adjusters is damaged. If the foot adjusters do not lock completely, move the foot adjusters a little before locking.
Basic operations
To project the picture 54
IN PU T M U TE
ZO O M
S CU FO
72
O N LA M P TE AN ST N /O M P D
2 4
STANDBY/ON
MUTE
FOCUS
ZOOM
VOLUME
1 2 3 4 5 6 7
Turn the MAIN POWER switch of the projector on. [ I : ON]
·The ON indicator will light up orange.
Press the STANDBY/ON button.
·The ON indicator blinks (green) and then lights (green). ·The ON indicator will blink green during warm-up and light up.
Turn the lens cover lever down.
·Lens cover opens.
Adjust the picture size using the ZOOM button. (2) Adjust the focus so that the picture is clear using the FOCUS button. (3) When any other button is pressed, "FOCUS" on the screen will be turned off.
Power on all connected equipment.
The method of connecting various equipment, see on the page 19 27.
Press the INPUT button or the INPUT SELECT (VIDEO or RGB) button to select the source of the signal Example on-screen display to be projected on the screen.
·The selected signal input is displayed at the bottom right of the screen.
RGB 1
BY
U EN M
T SE RE
POSITION ON
LASER
5
RESET MENU ON RIGHT MOUSE ON TIMER VIDEO 1/2 INPUT
1 3
7
BLANK RGB 1/2
+++FOCUS+++
Basic operations (continued)
To turn off the power 1
O N LA M P TE AN ST N /O M P D BY IN PU T M U TE
ZO O M
S CU FO
1
STANDBY/ON
MUTE
1 2 3
Press the STANDBY/ON button, for 1 second.
·The ON indicator lights up orange and the lamp turns off. (About 1 minute later), the fan stops and the indicator blinks orange. ·Press the STANDBY/ON button for short time (less than 1 second), the projector do not set in standby mode.
Turn the MAIN POWER switch of the projector off. [ Turn the lens cover lever up.
·Lens cover closes.
Caution Do not turn off the MAIN POWER switch before pressing the STANDBY/ON button. After the STANDBY/ON button is pressed, the fan rotates for about 1 minute to cool the projector. Do not turn off the MAIN POWER switch during the lamp on because the lamp is damaged.
PLUG & PLAY
This projector complies with VESA DDC1/2B specifications. [. . . ] Remove the air filter from the bottom.
Cleaning the air filter (continued)
3 4
Clean the air filter using a vacuum cleaner.
If dirt is still present, wipe the air filter with a cloth moistened with water or neutral detergent and wipe with a dry cloth.
Re-install the air filter.
Caution · If air filter is stutted with dust, etc. , protection circuit will turn the power off. · "CHECK THE AIR FLOW" is displayed when you block the ventilation holes.
Lamp
The following symptoms may indicate a worn lamp : · A dark picture. (Estimated operating time is approximately 2, 000 hours) Also LAMP indicator will light when the lamp becomes too hot. If LAMP indicator still lights up red, contact your dealer.
Message table
On screen display
The following messages are displayed on the screen.
MESSAGE CHANGE THE LAMP "CALL A MAINTENANCE PERSON. "
Action Lamp has 1, 900 hours on and it may need to be changed.
*1
"CHANGE THE LAMP" Lamp has 1, 980 hours on. [. . . ]