[. . . ] 6 Mounting the Tuner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Installing the Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Optimum Antenna Mounting Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Wiring and Cable Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] FCC Warning: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in this User Guide. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. Note: This equipment has been tested and found to comply with Part 15 of the FCC Rules. These rules are designed to provide reasonable protection against harmful interference. This equipment may cause harmful interference to radio communications if it is not installed and used in accordance with these instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of more of the following measures: · Relocate the receiving antenna. · Consult the dealer or an experienced technician for help. 4 SIR-PNP2 Installation Guide This symbol means important instructions. Failure to heed them can result in injury or material property damage. Return the unit to your authorized retailer or nearest service center for repairing. · Route the cable from the lowest point of the rear window into the trunk. Take advantage of any existing cable channels or wiring conduits. SIR-PNP2 Operation and Installation Guide Installation Guide SUV/Mini-Van Truck Convertible (only) Caution: · Do not pull the wire across sharp edges that could damage it. · Keep the wire away from areas where it could become tangled in the driver's and passenger's feet. · Keep the antenna wire away from extreme heat ­ like exhaust systems. · Avoid placing the cable near any moving parts. 7 7 Wiring and Cable Connections Antenna Input Connect the right-angle SMB connector from the antenna. Push firmly to attach. A Ai-NET Output Connector Use the supplied Ai-NET cable to connect to the Alpine Headunit or Audio Processor ­ See "System Connection Examples" for more specific details. Ai-NET Input Connector Connect to optional Alpine audio equipment like CD Changers - See "System Connection Examples" for more specific details. Power Harness Connector After the wiring connections are complete, plug the wiring harness into the connector. Make sure to insert firmly to lock the connector in place. B C D 1 2 A Antenna Input (SMB) B Ai-NET Output Connector (BLACK) C Ai-NET Input Connector (GRAY) D Power Connector 3 4 1 Open 2 Battery (+) 3 Chassis Ground (­) 4 Open 8 SIR-PNP2 Installation Guide Right-angle SMB Connector Antenna (21' cable) - Mount on Roof of Vehicle Power Harness Yellow ­ Connect to Battery Positive Black ­ Connect to Chassis Ground 2. 5-meter Ai-NET Cable (Connect to Alpine SAT Ready Headunit or Signal Processor) Note: It is important to follow the Input/Output configuration of the Ai-NET system. Gray Ai-NET connectors are Audio Input Black Ai-NET Connectors are Audio Output. (Exception is the connector on an Alpine Headunit ­ it can be either Input or Output depending on the position of the Ai-NET switch on the bottom of the unit. [. . . ] 2326. 250MHz Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-16 Volts DC Fuse Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1/8" x 5" x 1-3/8 (W XHXD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105mm x 126mm x 35mm (WxHxD) Chassis Size (with Mounting Tabs) . . . . . . . . . . . . . . . . . . . . [. . . ]