[. . . ] MIXING CONSOLE
Owner's Manual
Making the Most Of Your Mixer
Pages 6 to 18
E
Precautions
--For safe operation--
WARNING
Installation
G G
G
G
G
Connect this unit's AC power adaptor only to an AC outlet of the type stated in this Owner's Manual or as marked on the unit. Do not allow water to enter this unit or allow the unit to become wet. Do not place a container with liquid or small metal objects on top of this unit. Liquid or metal objects inside this unit are a fire and electrical shock hazard. [. . . ] Channel Inserts for Channel-specific Processing
Another way to get the mixer's signal outside the box is to use the channel inserts. The channel inserts are almost always located before the channel fader and, when used, actually "break" the mixer's internal signal path. Unlike the AUX sends and returns, the channel insert only applies to the corresponding channel. Channel inserts are most commonly used for applying a dynamics processor such as a compressor or limiter to a specific channel--although they can be used with just about any type of in/out processor.
Channel Fader
When a plug is inserted into the channel insert jack, the internal signal path is interrupted and sent outside the mixer for external processing.
Channel insert jacks must be used with a special insert cable that has a TRS phone jack on one end and mono phone jacks on the split "Y" end. One of the mono phone jacks carries the "send" signal to be fed to the input of the external processor, and the other carries the "return" signal from the output of the processor.
To the input jack of the external processor To the INSERT I/O jack Sleeve Sleeve Ring Tip Tip
To the output jack of the external processor
MG16/6FX
15
Making the Most Of Your Mixer
5
Making Better Mixes
Example2:
Funky R&B Groove The approach will be totally different if you're mixing a funky R&B number that centers on the groove. In this case most engineers will start with the drums, and then add the bass. The relationship between the drums and bass is extremely important to achieve the "drive" or groove the music rides on. Pay particular attention to how the bass works with the kick (bass drum). They should almost sound like a single instrument-- with the kick supplying the punch and the bass supplying the pitch. Once again, there are no rules, but these are concepts that have been proven to work well.
5-1. Well, you can do it that way, but a more systematic approach that is suited to the material you're mixing will produce much better results, and faster. There are no rules, and you'll probably end up developing a system that works best for you. Here are a few ideas to get you started:
Faders Down
It might sound overly simple, but it is usually a good idea to start with all channel faders off--all the way down. It's also possible to start with all faders at their nominal settings, but it's too easy to lose perspective with this approach. Start with all faders down, then bring them up one by one to fill out the mix. But which channel should you start with?
Music First--Then Mix
In any case, the music comes first. Think about the music and let it guide the mix, rather than trying to do things the other way around. What is the music saying and what instrument or technique is being used to drive the message?You're using a hightech tool to do the mixing, but the mix itself is as much art as the music. Approach it that way and your mixes will become a vital part of the music.
Example1:
Vocal Ballad Backed by Piano Trio What are you mixing?This means bringing the vocal channel up to nominal first (if your level setup procedure has been done properly this will be a good starting point), and then adding the other instruments. What you add next will depend on the type of material you are working with and your approach to it. [. . . ] reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. European Models Purchaser/User Information specified in EN55103-1 and EN55103-2. Inrush Current: 6A Conforms to Environments: E1, E2, E3 and E4
MG16/6FX
29
Appendix
Dimensional Diagrams
393
H 108 101. 3
3
W 423
31. 5
428
480
27. 5
Unit: mm
When mounted on rack
30
MG16/6FX
309. 6 D 416. 6
Appendix
Block Diagram and Level Diagram
MG16/6FX
31
For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. [. . . ]