[. . . ] If the plug is a moulded-on type, the fuse cover must be re-fitted when changing the fuse using a 13 Amp Asta approved fuse to BS 1362. In the event of losing the fuse cover, the plug must NOT be used until a replacement fuse cover can be obtained from your nearest electrical dealer. The colour of the correct replacement fuse cover is that as marked on the base of the plug. If your appliance is not fitted with a plug, please follow the instructions provided below:
B)
WARNING - THIS APPLIANCE MUST BE EARTHED IMPORTANT The wires in the mains lead are coloured in accordance with the following code: Green and yellow: Earth Blue: Neutral Brown: Live
As the colours of the wires in the mains lead may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The green and yellow wire must be connected to the terminal in the plug marked with the letter E or the earth symbol or coloured green or green and yellow. [. . . ] For each mode selected, the appliance will automatically choose the optimum values for maximum comfort.
22
GB-5750004200
11-02-2004
9:12
Pagina 23
REMOTE CONTROL
Inserting the batteries · Slide the cover as shown in figure. · Insert two new batteries (not rechargeable) making sure the (+) and (-) are in the correct positions. · Put the cover back on, letting it slide into its original position. · The Display will show all of the remote control's symbols for several seconds. If the remote control is to be replaced or thrown away, the batteries must be removed and disposed of in accordance with the current laws as it represents an environmental hazard. When the remote control unit batteries are replaced, the air-conditioning indicator and heating indicator will flash alternately on the remote control unit liquid crystal display. To set the remote control unit correctly, while is displayed, press any button. If you do not press a button within 12 seconds, the remote control unit will also make the heating mode available, despite the fact that this function is not available with this appliance.
PROPER USE
· · Point the remote control unit towards the airconditioning unit signal receiver. Maximum distance: about seven (7) metres (without any obstacle between remote control and receiver). A beep indicates that the air-conditioning unit is on and the symbol flashes on the display. Press the MODE button a number of times until the dehumidifying symbol appears on the display. The symbol is displayed
High
· ·
.
High
Low
Low
· ·
Press the button to increase the dehumidifying level and the button to reduce it. In dehumidifying mode, fan speed is selected by the appliance automatically.
FAN MODE
On humid but not particularly hot days, the fan function alone may be adequate. A beep indicates that the air-conditioning unit is on and the symbol flashes on the display. · Press the MODE button a number of times until the fan symbol appears on the display. · Once fan mode has been selected, press the FAN button until the required speed is reached (low, medium, high).
25
GB-5750004200
11-02-2004
9:12
Pagina 26
SMART MODE
In SMART mode, the air-conditioning unit decides the best way to operate to guarantee maximum comfort. A beep indicates that the air-conditioning unit is on and the symbol flashes on the display. The appliance functions automatically and the symbol appears on the display. However, if the required temperature has not yet been reached, it can be reduced or increased by a maximum of 2° C by pressing the buttons. It should be pointed out that when the automatic ventilation functions are activated, the appliance itself will choose the proper speed.
High
Low
AUTOMATIC SLEEP MODE
The automatic SLEEP mode is ideal for the night-time as it enables operation of the air-conditioning unit in any of the modes (air-conditioning, dehumidifying, fan or SMART) to be gradually reduced until it shuts down completely (after eight hours). To select SLEEP mode, proceed as follows: · Press the button to turn the appliance on. · A beep indicates that the air-conditioning unit is on and the symbol flashes on the display. [. . . ] For this reason, it is a good idea to clean the filter Remove the air filter as shown below.
· · ·
·
Filter
;; ;;;; ;;;; ;;;
·
·
Use a vacuum cleaner to remove the dust on the filter. If the filter is very dirty, dip it in warm water (of less than 40° C. ) and rinse it several times. After having washed the filter, let it dry completely before putting it back in place.
CHECKS TO MAKE AT A SEASON'S BEGINNING
Check to make certain that the power cable and the electrical outlet are in perfect condition and that there is a suitable earthing system. Give strict observance to all installation norms.
WORK TO BE DONE AT A SEASON'S END
Turn off the air-conditioner. [. . . ]