[. . . ] I m p o r t a n t s a f e g u a rd s
· Use this appliance only as described in this instruction manual. As with any electrical appliance, the instructions aim to cover as many eventualities as possible. Caution and common sense should be used when operating and installing this air conditioner. · This appliance has been manufactured to cool and dehumidify domestic environments and should not be used for other purposes. [. . . ] Whenever the plug is disconnected or if there is a power failure, the programmer stops (the clock is then "slow") and must be re-set.
9
ENGLISH
Selecting functions
AIR CONDITIONING FUNCTIONS
To turn the unit on in air conditioning mode, proceed as follows: 1. Press the ON/OFF button 11 (the signal light
10 will come on).
COOL JET
The cool Jet mode provides the appliance with greater cooling capabilities. This is particularly useful when you want to bring the temperature of a very warm room quickly down to a more comfortable level. In this case: Make sure that the tank is full of water (see page 8); Make sure that the function selector switch
19 is in the HIGH position.
2. Rotate the function selector 19 dial counter-clockwise: · Place the function selector in the HIGH position to operate the unit in air conditioning mode at maximum fan speed, after 3 minutes the signal light 15 will come on. to operate the unit in air condtioning mode at minimum fan speed after 3 minutes the signal light 16 will come on. Now set the required temperature by rotating the room thermostat dial 20 .
Press the Cool Jet button 22 , after three minutes , the signal light 21 , 15 or 16 with come on. After reaching the desired temperature, you can release the Cool Jet button and reposition the selector switch to the LOW position This will provided quite operation.
VENTILATION/FILTRATION
Rotate the function selector 19 clockwise. · Press the ON/OFF button 11 (the signal light 10 will come on). · Place the function selector on the "FreshZone" position and choose the desired fan speed (min/max). The signal light 17 18 or will come on).
Note
The temperature is not expressed in degrees. We recommend that you turn the thermostat dial to the maximum position. When the desired room temperature has been reached, slowly turn the thermostat in a clockwise direction until it arrives at the position where a click can be heard. The temperature selected in this way will automatically regulate and maintain the temperature and save energy. When regulating the thermostat, the air conditioning function is temporarily interrupted and the unit continues to operate in fan only mode. In this way, the appliance keeps the air temperature within the room constant.
PROBLEM WARNING LIGHT
23 The pilot light indicates that the safety device of the pressure switch has switched on. To restore the proper functioning of the appliance, eliminate the possible causes of the problem and press the restore button 6 .
The causes may be: 1) Water has accumulated in the exhaust hose: in this case, it is necessary to drain the water out of the machine, outwards (never towards the air conditioner) and eliminate the water in the hose. 2) The exhaust hose is obstructed: eliminate the obstacles that obstruct the release of air to the outside. If, after having repositioned the drainage tube, the machine still does not start up, the problem might be more complicated (ex. : obstructed ventilation fan) and could require the assistance of a Delonghi Authorized Service Center.
Delay on Start Up
1. A special safety device will delay the start of air conditionig by approximately 3 to 5 minutes when switching between functions or on initial start up. You may also experience a slight delay between changing from one function to another.
10
Recommendations
ELECTROSTATIC FILTration
In addition to dust, this filtration system is able to capture even the smallest sized particles and impurities such as cigarette smoke. The electrostatic white filter should never be used with the permanent washable filter, (black) which is also included with the appliance. [. . . ] ATTENTION: The use of products other than De' Longhi could cause damage to the internal components of the appliance and invalidate the terms of the warranty.
13
ENGLISH
Troubleshooting/Technical specification
If the unit is not working properly, this may be due to small problems check you can easily resolve yourself. Follow these instructions carefully before contacting your local Authorized Delonghi Technical Service Center.
PROBLEM
The air conditioner is · completely turned · off The air conditioner is on (signal light 10 ) · but the appliance doesn't start The unit works but does not cool the room ·
CAUSE
It is not plugged in There is no electricity
· plug in
SOLUTION
The notches of the timer are in the rest mode ·
Proceed with a new timr setting. Wait three minutes (safety device) and the appliance should start cooling. Close the windows Eliminate heat sources Fit the hose in the coupling Lower the thermostat Clean/replace filters
Three minutes have not passed since it was · turned on Windows open A heat source is operating in the room (burner, light, etc. ) or there are a lot of people The air outlet hose has detached from the coupling Thermostat adjusted too high Air filters clogged The output of the unit is insufficient for the conditions or size of the room There is a kink in the exaust hose The exaust hose is blocked · · · · ·
· · · · · · The unit works for only a short time · ·
· ·
· ·
There are too many curves in the outlet tube The fan is blocked
· ·
Position the exaust hose correctly Check that there are no blockages preventing the discharge of air to the outside Rearrange the hose correctly Contact the De'Longhi Service Center
TECHNICAL SPECIFICATION
Power supply RECOMMENDED OPERATING CONDITIONS Max. [. . . ]