[. . . ] Operation Guide
Please read this Operation Guide before using the printer. Keep it close to the printer for easy reference.
Please read the Operation Guide before using the printer. The sections of this guide and parts of the printer marked with symbols are safety warnings meant to protect the user, other individuals and surrounding objects, and ensure correct and safe usage of the printer. WARNING: Indicates that serious injury or even death may result from insufficient attention to or incorrect compliance with the related points. [. . . ] Plain
6
Press the 3 or 4 key to display the desired cassette type. Plain Preprinted Bond Recycled Rough Letterhead Color Prepunched Custom(1 to 8)
7 8
When the desired paper source displayed, press the ENTER key. The message display returns to Ready.
Setting Duplex Printing Using the duplex unit, you can automatically print on both sides of the paper. Q Binding Setups The term binding refers to the manner in which printed pages of paper are joined together (by gluing, stitching, etc. ) in book form. The two possible types of binding are long-edge binding, in which pages are joined together along their long edge; and short-edge binding, in which they are joined together along their short edge. In selecting a binding type, you must also consider the orientation of the printed page. You can use long-edge or short-edge binding with either landscape or portrait printing. Depending on the binding type and print orientation, the duplex unit provides four types of binding setups. These are: (1) portrait, long-edge, (2) portrait, short edge, (3) landscape, longedge, and (4) landscape, short-edge. The figure below shows these binding setups.
(1) Portrait, long-edge (2) Portrait, short-edge
7 8
When the desired cassette type is displayed, press the ENTER key. The message display returns to Ready.
Selecting the Paper Source You can select from which paper source printing will be performed. If no option units are installed, the only selections are the paper cassette and MP tray of the printer. If option paper feeders are installed, they can also be selected.
1 2
Press the MENU key.
Press the 3 or 4 key repeatedly until Paper Handling > appears.
Paper Handling >
3 4
Press the 2 key.
Landscape, long-edge
(3) (4)
Landscape, short-edge
Press the 3 or 4 key repeatedly until >Feed Select appears.
>Feed Select Cassette1
Binding Setups To select duplex printing and binding setup from the operator panel, proceed as follows.
3-43
Chapter 3 Using the Operator Panel
1 2
Press the MENU key.
4
Press the 3 or 4 key repeatedly until >Stack Select appears.
Press the 3 or 4 key repeatedly until Paper Handling > appears.
>Stack Select Finisher F-down
Paper Handling >
5
Press the ENTER key. The selected output device will be displayed.
3 4
Press the 2 key.
>Stack Select ?Finisher F-down
Press the 3 or 4 key repeatedly until >Duplex Mode appears.
6
Press the 3 or 4 key to display the desired destination. Face-down tray Finisher F-up Finisher F-down
>Duplex Mode None
5
Press the ENTER key. A blinking question mark (?) appears.
7 8
When the desired paper source displayed, press the ENTER key. The message display returns to Ready.
>Duplex Mode ?None
6
Press the 3 or 4 key to display the desired duplex mode. None (default) Short edge bind Long edge bind
Adjusting the Stitch Positions When installing the option document finisher DF-75, adjust the stitch positions using the following procedures. In the default settings, the stitch position is set in the center of the paper. The adjustment can be done by moving the stitch position adjustment gear in the document finisher. For example, select the range from -57 to +57 (1 = approximately 0. 14 mm) to move the stitch position approximately 8 mm as shown in the following figure. The default setting is 000 (center of the paper. ) Default stitch position (center of the paper)
7 8
When the desired duplex mode is displayed, press the ENTER key. [. . . ] The Print dialog box will be displayed.
NOTE The Multiple virtual mailbox tray number can be specified at a time using commas (, ) and hyphen (-).
The Mailbox Name will be displayed in the Defined Names list box.
2
Click on the Name drop down list, all the printers installed under Windows are listed. Select Kyocera Mita FS-9100DN KX or Kyocera Mita FS-9500DN KX.
8 9 10
Click the OK button to quit the Hard Disk Settings dialog box. In the Kyocera FS-9100DN KX Properties dialog box, click the OK button. Click the X button in the upper-right side of the dialog box.
3 4
Select the range of the pages you want to print in the document, All or Current page in Page range. [. . . ]