[. . . ] INSTRUCTION MANUAL
VHF/UHF DUAL BAND FM TRANSCEIVER
iP7A
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIO TELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.
FOREWORD
Thank you for purchasing this Icom product. The IC-P7A VHF/UHF DUALBAND FM TRANSCEIVER is designed and built with Icom's superior technology and craftsmanship. [. . . ] qWhile pushing and holding [FUNC], push and hold [SQL] (ATT·SET) for 1 sec. to enter set mode.
[DIAL] · OFF · DUP ONLY · DUP TONE · OFF · ON
USA/KOREA versions only eWhile pushing and holding [FUNC], rotate [DIAL] to select the desired condition. (default)
Korea version:
r Push [SQL] (ATT·SET) to exit set mode.
D Frequency range and offset direction
· U. S. A. version: Frequency range
SCAN
Duplex direction "" appears "+" appears "+" appears "" appears
S. MW
145. 200145. 495 MHz 146. 610146. 995 MHz 147. 000147. 395 MHz 442. 000444. 995 MHz
DTCS ATT
SET
SET
wRotate [DIAL] to select "AUTORP. "
WFMAM -DUP T SQL
DTCS ATT
WFMAM -DUP T SQL
447. 000449. 995 MHz · Korea version: Frequency range 439. 000440. 000 MHz
VOL PRIO P SKIP MR 9 5 LOW 1
After 1 sec.
VOL PRIO P SKIP MR 9 5 LOW 1
Auto repeater item
Setting indication
Duplex direction "" appears
23
MEMORY/CALL CHANNELS
General description
The IC-P7A has 1050 memory channels including 50 scan edge memory channels (25 pairs) for storage of often-used frequencies. And a total of 18 memory banks, A to H, J, L, N, O to R, T, U and Y are available for storing groups of frequencies, etc. Up to 100 channels can be assigned into a bank.
6
Memory channel programming
q Push [V/M] (SKIP·S. MW) to select VFO mode. w Set the desired frequency: Select the desired band with [BAND] (TS·LOCK). offset frequency, duplex direction, subaudible tone frequency, etc. ), if desired. to enter select memory write mode.
· 1 short and 1 long beep sound. ·" " indicator and memory channel number blink.
D Memory channel contents
The following information can be programmed into memory channels: · Operating frequency (p. 14) · Duplex direction (DUP or DUP) with an offset frequency (pgs. 39).
5 6
r Rotate [DIAL] to select the desired channel.
· Call channels (C0, C1), VFO (VF) and scan edge channels (00A/00b to 24A/24b), as well as regular memory channels, can be programmed in this way. · While pushing and holding [FUNC], rotate [DIAL] to select memory channel in 10 channel steps.
t Push and hold [V/M] (SKIP·S. MW) for 1 sec.
· 3 beeps sound · Memory channel number automatically increases when continuing to push [V/M] (SKIP·S. MW) after programming.
[EXAMPLE]: Programming 145. 870 MHz into memory channel 20 (blank channel).
Push
WFMAM -DUP T SQL
S. MW
for 1 sec.
WFMAM -DUP T SQL
Rotate
DTCS ATT
WFMAM -DUP T SQL
Push
DTCS ATT
S. MW
for 1 sec.
WFMAM -DUP T SQL
DTCS ATT
DTCS ATT
WFMAM -DUP T SQL
DTCS ATT
VOL PRIO P SKIP MR 9 5 LOW 1
VOL PRIO P SKIP MR 9 5 LOW 1
VOL PRIO P SKIP MR 9 5 LOW 1
VOL PRIO P SKIP MR 9 5 LOW 1
VOL PRIO P SKIP MR 9 5 LOW 1
24
6
MEMORY/CALL CHANNELS
Memory bank setting
The IC-P7A has a total of 18 banks (A to H, J, L, N, O to R, T, U and Y). Regular memory channels, 000 to 999, may assigned into a desired bank for easy memory management. to enter select memory write mode.
· 1 short and 1 long beep sound. ·" " indicator and memory channel number blink.
rWhile pushing and holding [BAND] (TS·LOCK), rotate [DIAL] to select the desired bank.
· Banks A to H, J, L, N, O to R, T, U and Y are available. · The bank can also be selected by pushing [BAND] (TS·LOCK) several times. Bank is selected with
WFMAM -DUP T SQL
+
w Rotate [DIAL] to select the desired memory channel. eWhile pushing and holding [CALL] (MODE·SCAN), rotate [DIAL] to select "BANK. "
· After releasing [CALL] (MODE·SCAN), "-- -- -- --" is displayed instead of the frequency indication, and only " " indicator blinks. · Bank group and channel number is displayed if the selected memory channel has already been assigned to a bank. · "BANK" can can also be selected by pushing [CALL] (MODE·SCAN) several times. [DIAL]
WFMAM -DUP T SQL
DTCS ATT
VOL PRIO P SKIP MR 9 5 LOW 1
t Rotate [DIAL] to select the desired bank channel number.
· Vacant bank channel numbers are only be displayed. [. . . ] NOTE: Connect the HM-153P after removing the [MIC/SP] cap (MIC/SP jack cover). Keep the [MIC/SP] cap attached when jack are not in use to keep the contact clean.
OPC-782 Microphone Microphone
HM-153 Speaker/MIC connector
HM-153P
15
SCAN SCAN
S. MW S. MW
SET
SET
78
15
OPTIONS
D LC-161 CARRYING CASE
Helps protect the transceiver from scratches, etc. NOTE: When using as below illustration, tension release loop protects the [MIC/SP] connector from being damaged by cable stress or vibration OPC-782 HM-128
D HM-128 EARPHONE MICROPHONE
An optional OPC-782 is required for connection.
q w
Transceiver
D HM-131 SPEAKER MICROPHONE
An optional OPC-782 is required for connection. HM-131 LC-161 Tension release loop
e
79
POCKET GUIDE
Important operating instructions are summed up in this and the following page for your simple reference. [. . . ]