[. . . ] These limits are designed to provide reasonable protection against harmful interference when the device is operated in a residential environment. This device generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If you determine the device does cause harmful interference to radio or television reception (this may be determined by monitoring the interference while turning the device off and on), you are encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. [. . . ] In this case, the screen is recovered slowly by changing the image or turning off the Power Switch for hours. Contact your dealer or iiyama service center for the backlight replacement when the screen is dark, flickering or not lighting up. Non condensing when the unit is in-use, it will cause defective symptoms.
ENGLISH
CUSTOMER SERVICE
NOTE The fluorescent light used in the LCD monitor may have to be periodically replaced. For the warranty coverage on this component, please check with local iiyama service center. If you have to return your unit for service and the original packaging has been discarded, please contact your dealer or iiyama service center for advice or replacement packaging.
CLEANING
WARNING CAUTION NOTE If you drop any materials or liquids such as water into the monitor when cleaning, unplug the power cable immediately and contact your dealer or iiyama service center. For safety reasons, turn off the power switch and unplug the monitor before you clean it. To protect the LCD panel, do not scratch or rub the screen with a hard object. Thinner Spray-type cleaner Benzine Wax Abrasive cleaner Acid or Alkaline solvent Touching the cabinet and the LCD screen with any product made from rubber or plastic for a long time may cause degeneration or loss of paint on the cabinet and the LCD screen. Stains can be removed with a cloth lightly moistened with a mild detergent solvent. Stains can be removed with a cloth lightly moistened with a mild detergent solvent. Don't pour the detergent solvent on the touch screen.
CABINET LCD SCREEN
3
FOR YOUR SAFETY
BEFORE YOU OPERATE THE MONITOR
FEATURES
ProLite T1530SR : 38cm (15. 0") TFT Color LCD Monitor Resistive Film
ENGLISH
4
ProLite VK248H : 43cm (17. 0") TFT Color LCD Monitor Resistive Film ProLite T1930SR : 48cm (19. 0") TFT Color LCD Monitor Resistive Film ProLite T1530SR: Supports Resolutions up to 1024 × 768 ProLite VK248H / ProLite T1930SR : Supports Resolutions up to 1280 × 1024 Digital Character Smoothing Automatic Set-up Plug & Play VESA DDC2B Compliant Windows® 95/98/2000/Me/XP/Vista Compliant Power Management (VESA DPMS Compliant) ProLite T1530SR : VESA Standard (75mm×75mm) for Arm or Wall Mounting ProLite VK248H / ProLite T1930SR : VESA Standard (100mm×100mm) for Arm or Wall Mounting Stereo Speakers
SPECIAL NOTES ON TOUCH PANEL
Permanent damage can occur if Sharp Edged, Pointed or Metal items are used to activate Touch. Touch screen driver software Touch screen driver software and system may not start when you start your computer while touching the screen. Touch screen driver software may not run due to the power saving function depending on the BIOS of your computer. In this case, set the power saving function to off.
ADJUSTING THE VIEWING ANGLE
For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference. Hold the panel so that the monitor does not topple when you change the monitor's angle. You are able to adjust the monitor's angle up to 90 degrees upward, 5 degrees downward. Careful attention is required not to catch your fingers or hands when you change the angle.
5° 90°
BEFORE YOU OPERATE THE MONITOR
8
ENGLISH
OPERATING THE MONITOR
To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT TIMING shown on page 21. You are also able to adjust the picture by following the button operation shown below. For more detailed adjustments, see page 13 for SCREEN ADJUSTMENTS.
( Press the Menu Button to start the On Screen Display feature. There are
additional menu pages which can be switched by using the
1280x1024 ANALOG CONTRAST BRIGHTNESS VOLUME AUTO TUNE H-POSITION V-POSITION LANGUAGE EXIT
/
Buttons.
ENGLISH
Adjustment icon
EXIT
SELECT Page Menu page
B Use the +/ Buttons to make the appropriate adjustment or setting.
For example, to correct for vertical position, press the Menu Button. display should be changing accordingly while you are doing this.
1280x1024 ANALOG CONTRAST BRIGHTNESS VOLUME AUTO TUNE H-POSITION V-POSITION LANGUAGE EXIT The bar shows the progress of the adjustment being made.
(V-
Use the +/ Buttons to change the vertical position settings. The vertical position of the overall
EXIT
SELECT Page
NOTE Any changes are automatically saved in the memory when the On Screen Display disappears. [. . . ] When activated, it automatically reduces unnecessary power consumption of the monitor when your computer is not in use. To use the feature, the monitor needs to be connected to a VESA DPMS compliant computer. There is a power management step the monitor takes as described below. The power management function, including any timer settings is configured by the operating system. [. . . ]