[. . . ] Bottom pivot guide
Note: If your product is without lock, there is no closing clip(8). PLACE YOUR CABINET
(1) When moving your wine cabinet, do not incline it more than 45o, and always toward side where the power lead is located. (2) In order to reduce the working time and save power, place your cabinet at where the temperature is between 5oC~32oC, and there should be space to allow air to flow around the cabinet, so the heat produced by condenser can be eliminated in time. Leaving a space of at least 8cm between the wall and the back of your wine cabinet and 5 cm on the sides and at the top. [. . . ] 3 Installing the wooden shelf See diagram below to install your wooden shelf. 6 The installation of the wall separate screws When the back side of wine cellar placed against the wall, should need to install the wall separate screws. As shown, the wall separate screws were installed in the flange on both sides of compressors pallet. 1
Status Lock
Function Unlock
Control process Press “ seconds ”and hold for 3
LCD display Lock “ off “ symbol ”turns
Remark When lock symbol is on, “ ”/ “ ”/
”do not respond for pressing
2
Unlock
Enter temperature setting Temperature setting
Press “
”, and enter
Temperature symbol flashing Temperature symbol’s digit change
temperature setting Press “ ”to increase
3
temperature, and press “ ”to decrease temperature 4 Temperature setting Changing between: “ ℃ ” and “℉” Carbon filter Press and hold “ 6 ” for 5 seconds to check filter remain life Press and hold “ seconds, and press “ Light mode switching ”for 5 ” to Press “ ” after finished setting 5 Press and hold “ seconds ” for 5
Display current cabinet temperature Temperature symbol change
Safe temperature setting and exit temperature setting function
restart counting for 365 days 7 Press and hold“ ”for 5 , , : light on when door open : Light on always : light off always
seconds to enter light switching mode
8
Humidity display
Press“
”and “
20
”at
Temperature display change to
same time 9 Temperature fine-tuning Press “ ”enter temperature
humidity display
setting, and press and hold “ ” &“ ”at same time for
more than 3 seconds, then press " "for increasing temperature by 0. 2ºC or press“ 10 Stand by mode Wake up stand by mode Factory reset Press and hold “ “ / ” “ / ” ” for Wine cooler turn off Display lighting turn off and indicate
decreasing temperature by 0. 2ºC Press and hold “ than 5 seconds 11 Press “ ” ” more for
12
”for more than 5 seconds
4. 3 Alarm explanations “Door open” alarm will flash when the door is opened for 1 minute and 2 minutes, the buzzer will ring
five times per 1 minute, the LCD display will flash until the door is closed. When the door is opened for 3 minutes, the buzzer will ring 1 minute, the LCD will flash until the door is closed. Invalidation of carbon filter” alarm: When the carbon filter is disabled, “ filter and press “ “ ” for 5 seconds, the LCD will display ” will flash. Change the carbon ”, then pressing
when pressing “
”again to confirm the setting. 4 Humidity alarm When the relative humidity is less than 50% or more than 90%, and last for 24 hours, the display symbol “ 90%. The symbol should stop flashing until the humidity recovers to more than 50% or less than
21
4. 5 Heater failure alarm When the sensor detects that the temperature is deviated 4ºC for 24 hours, “ ring, pressing “ ” or “ ”, the buzzer stops, but “ ” will flash and buzzer will
” keeps flashing until deviate less than 4ºC. When the cabinet temperature is higher than 32ºC, LCD display will show “ hours, LCD and backlight will flash, buzzer will alarm. Only LCD flashes and shows “ ”, if the status lasts for 3 ”, buzzer will not
” or “
”, until temperature is normal. , if the status lasts for 3 ” or “ ”, buzzer will not
4. When the cabinet temperature is lower than 0ºC, LCD display will show “ hours, LCD and backlight will flash, buzzer will alarm. Only LCD flashes and shows “
”, until temperature is normal. When the setting temperature is lower than the internal temperature of the cabinet, the machine will start to work and refrigeration. When the setting temperature is higher than the internal temperature of the cabinet, the machine will
stop working and stop the cooling, heating wire will begin to work to maintain cabinet temperature equilibrium. [. . . ] Appareils de réfrigération polyvalents et de type autre
24
Désignation
Marque / Trade mark CTP300/MC320 TRV300 CTPE204/CTPE24 8
CTV250/MC250 CTVN220/TRV250
LA SOMMELIERE CTP205 TRP205 2 CTV205 TRV205 CTP175 MC175P TRP175 CTV175 MC175V TRV175 CTP140 MC140P TRP140 CTV140 MC140 TRV140 CTV80 MC83 TRV83
Référence du modèle / Model reference Catégorie du modèle d’appareil de réfrigération / Category of the household refrigerating appliance model Classe d’efficacité efficiency class énergétique / Energy
CTP250/TRP250 LS248B/MC250P
D
A
E
C
C
E
C
E
C
E
D
Co nsommatio n d’énergie annuelle / Anual energy consumption
356
165/168
386
293
286
376
278
367
272
358
298
La consommation d’énergie est calc ulée sur la base du résultat obtenu pour 24 heures dans des conditions d’essai normalisées. la consommation d’énergie réelle dépend des conditions d’utilisation et de l’emplacement de l’appareil. / Energy consumption per year is based on standard test results for 24 hours. Actual energy co nsumption will depend on how the appliance is used and where it is located. [. . . ]