[. . . ] KDC-BT648U KDC-X695 KDC-X395 KDC-348U
CD-RECEIVER
INSTRUCTION MANUAL
AMPLI-TUNER LECTEUR DE CD
MODE D’EMPLOI
REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM
MANUAL DE INSTRUCCIONES
Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new CD-receiver. For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product. [. . . ] select “KENWOOD BT CD/R-3P1” , “KCA-BT300” or “KCA-BT200” from the list of connected units. Registering from this unit 1 KDC-BT648U / KDC-X695 Press to enter Bluetooth mode. KDC-X395 / KDC-348U Press and hold the volume knob to enter Bluetooth mode. 4 Turn the volume knob to select [DEVICE SEARCH], then press to enter. 2 Turn the volume knob to select
KDC-348U with KCA-BT300 only) If “PAIRING OK” is displayed, proceed to step 10. if “PAIRING OK” is displayed , registration is completed. If the error message appears even though the PIN code is correct, try Registering Special Bluetooth device. If there are 5 or more Bluetooth devices registered, you cannot register a new Bluetooth device. registering Special Bluetooth device 1 KDC-BT648U / KDC-X695 Press to enter Bluetooth mode. KDC-X395 / KDC-348U Press and hold the volume knob to enter Bluetooth mode. 6 Go through the procedure step 4 of <Registering from this unit> and complete the registration (pairing). If the device name is not in the list, select “OTHER PHONE”. 4 Turn the volume knob to select [PHONE
SELECT] or [AUDIO SELECT], then press to enter. If a cell-phone is already selected, deselect it, and then select a different one. KDC-X395 / KDC-348U Press and hold the volume knob to enter Bluetooth mode. 5 Search for the Phone Book name to register Select the name to register with reference to 5 in <Calling a Number in the Phone Book> (page 16). If a voice tag has already been registered for a name, “*” is displayed before the name. Selecting the Bluetooth Device
1 KDC-BT648U / KDC-X695
Press
to enter Bluetooth mode. Turn the volume knob to select “YES”, then press to confirm. When a beep is heard, say the same voice tag as that you said in step 7 within 2 seconds. registering Phone Book Name Type 1 KDC-BT648U / KDC-X695 Press to enter Bluetooth mode. KDC-X395 / KDC-348U Press and hold the volume knob to enter Bluetooth mode. [. . . ] 8 ft) Profile: HFP (Hands Free Profile), SPP (Serial Port Profile), HSP (Headset Profile), OPP (Object Push Profile), PBAP (Phonebook Access Profile), SYNC (Synchronization Profile) Audio section Maximum output power: 50 W × 4 Full bandwidth power (at less than 1 % THD): 22 W × 4 Speaker impedance: 4 Ω — 8 Ω Tone action: Bass: 100 Hz ±8 dB Middle: 1 kHz ±8 dB Treble: 12. 5 kHz ±8 dB Preout level / load (CD): KDC-X695/KDC-X395: 4, 000 mV/ 10 kΩ KDC-BT648U/KDC-348U: 2, 500 mV/ 10 kΩ Preout impedance: ≤ 600 Ω Auxiliary input section Frequency response (±3 dB): 20 Hz — 20 kHz Input maximum voltage: 1, 200 mV Input impedance: 10 kΩ General Operating voltage: KDC-BT648U/KDC-X695: (10. “Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. [. . . ]