[. . . ] Please read these operating instructions before using the unit and save them for future reference. consulte “Guía Rápida Española” , página 59. A B C D E F G *1 *2 *3 *4 *5 *6 A Accessory item/ Order number AC adaptor/PNLV226Z Telephone line cord/ PQJA10075Z Wall mounting adaptor/ PNKL1044Z2 Rechargeable batteries/ HHR-4DPA Handset cover*6/ PNYNTGEA20BR Belt clip/PNKE1312Z2 Charger/PNLC1050ZB 1 unit*1 2 units*2 3 units*3 4 units*4 5 units*5
Accessory quantity 1 1 1 2 1 1 – 1 1 1 4 2 2 1 1 1 1 6 3 3 2 1 1 1 8 4 4 3 1 1 1 10 5 5 4
KX-TGE210/KX-TGE240 KX-TGE212/KX-TGE232/KX-TGE242 KX-TGE233/KX-TGE243 KX-TGE234/KX-TGE244 KX-TGE245 The handset cover comes attached to the handset. Pdf4
4
2013/11/22
14:22:26
Introduction Additional/replacement accessories
Please contact your nearest Panasonic dealer for sales information (page 63). [. . . ] Displaying the handset name
You can select whether or not the handset name is displayed in standby mode. A MSAVEN a MOFFN To erase a number: MERASEN a MbN: “Yes” a MSELECTN a MOFFN Note: R When editing, press the desired dial key to add, MCLEARN to erase. A MSAVEN a MOFFN
Registering a unit
Operating additional units
Additional handsets
Up to 6 handsets can be registered to the base unit. Erasing all call block numbers 1 2 3 4 5
MMENUN#217 MbN: “Block a single number” or “Block range of numbers” a MSELECTN MMENUN a MbN: “Erase all” a MSELECTN MbN: “Yes” a MSELECTN MbN: “Yes” a MSELECTN a MOFFN
Registering a handset to the base unit
The supplied handset and base unit are pre-registered. If for some reason the handset is not registered to the base unit, re-register the handset. Other programming
Changing the handset name
The default handset name is “Handset 1” to “Handset 6”. You can customize the name of each handset (“Bob”, “Kitchen”, etc. To display the handset name in standby mode, turn on the handset name display feature (page 35). 1 2
Handset: MMENUN#130 Base unit: Press and hold MLOCATORN or MHANDSET LOCATORN for about 5 seconds. R If all registered handsets start ringing, press MLOCATORN or MHANDSET LOCATORN again to stop, then repeat this step. MSAVEN a MOFFN
3
Deregistering a handset
A handset can cancel its own registration to the base unit, or other handsets registered to
For assistance, please visit http://www. This allows the handset to end its wireless connection with the system. 1 2 3
MMENUN#131 R All handsets registered to the base unit are displayed. Talking Caller ID
Handset / Base unit*1 *1 KX-TGE230/KX-TGE240 series: page 3 This feature lets you know who is calling without looking at the display. To use this feature, you must: – subscribe to a Caller ID service of your service provider/telephone company. When caller information is received, the handsets and/or base unit announce the caller’s name or phone number received from your service provider/telephone company following every ring. R Caller ID service has a limit of how many characters can be displayed. If the caller’s name is too long, the unit may not be able to display or announce the entire name. Caller ID features
When an outside call is being received, the caller information is displayed. Caller information for the last 50 callers is logged in the caller list from the most recent call to the oldest. R If the unit cannot receive caller information, the following is displayed: – “Out of area”: The caller dials from an area which does not provide a Caller ID service. – “Private caller”: The caller requests not to send caller information. [. . . ] This Limited Warranty excludes both parts and labor for batteries, antennas, and cosmetic parts (cabinet). This Limited Warranty only applies to products purchased and serviced in the United States or Puerto Rico. This Limited Warranty is extended only to the original purchaser and only covers products purchased as new. Mail-In Service--Online Online Repair Request To submit a new repair request and for quick repair status visit our Web Site at http://www. [. . . ]