[. . . ] 40
Children from 8 years of age or people whose physical, sensory or mental abilities or their lack of experience or knowledge prevent them from using the appliance safely must not use this appliance without supervision or instruction by a responsible person. Before you switch ON the appliance Please read the operating and installation instructions carefully. They contain important information on how to install, use and maintain the appliance. Retain all documents for subsequent use or for the next owner.
4
Safety instructions
en
Delivery 1. [. . . ] The spray pressure in the lower basket is intensified, the rinsing temperature is increased slightly.
* depending on model Additional options can be set with the buttons X.
¿ Extra drying *
Extra drying
Expres Wash/Spe dPerfect(VarioSpe d)
Ÿ Express Wash/ Speed Perfect/ (VarioSpeed) *
An increased temperature during the final rinse and an extended drying phase ensure that even plastic parts dry better. There is a slight increase in the energy consumption.
This function can reduce the running time by approx. To obtain optimum cleaning results at a reduced running time, water and energy consumption are increased.
21
en
Operating the appliance
Operating the appliance
ga ntr iO e p eiph c at nl e a
Switching on the appliance
1. Note - for environmentally friendly operation of the dishwasher: The Eco 50° programme is a particularly environmentally friendly programme. According to EU regulation 1016/2010 it is the “Standard programme” which is the most efficient standard cleaning cycle for cleaning normally soiled utensils in terms of the combined energy and water consumption for cleaning these types of utensils.
Programme data
The programme data (consumption values) can be found in the summary of instructions. water temperature or line pressure may result in deviations.
Aquasensor
Aqua sensor *
* depending on model The Aqua sensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water. If the Aqua sensor is active, “clean” rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 3–6 litres. If the turbidity is greater, the water is drained and is replaced with fresh water. In the automatic programmes the temperature and running time can also be adjusted to the degree of soiling.
Remaining running time display
When the programme is selected, the remaining running time of the programme is indicated on the digital display H. The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme).
22
Operating the appliance
Timerprogram ing
en
Timer programming *
* depending on model You can delay the start of the programme in 1-hour steps up to 24 hours. Press button P until the displayed time corresponds with your requirements. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces. Stainless steel appliances: To prevent corrosion, avoid using sponge cloths or wash them out thoroughly several times before using for the first time.
m Warning – Health hazard
Never use other domestic detergents, e. g. containing chlorine!
Special salt and rinse aid
Check the refill indicators h and `. If required, refill salt and/or rinse aid.
25
en
Cleaning and maintenance
Filters
The filters 1R keep large foreign objects in the rinsing water away from the pump. The filter system consists of a coarse filter, a flat fine filter and a microfilter. Unscrew filter cylinder as illustrated and take out filter system.
Spray arms
Limescale and contaminants in the rinsing water may block nozzles and bearings on the spray arms 1: and 1B. Re-install filter system in reverse sequence and ensure that the arrow marks are opposite each other after closing the filter system.
4. 26
Fault, what to do?
en
Fault, what to do?
, tF l u a w t a h o t d ?o
Experience has shown that you can rectify most faults which occur in daily operation yourself. In the following overview you can find possible causes of malfunctions and helpful information for rectifying them. Note If the appliance stops during dishwashing or does not start for no obvious reason, first run the Abort programme function (Reset). [. . . ] 45 kg Voltage: 220–240 V, 50 Hz or 60 Hz Connected load: 2. 0–2. 4 kW Fuse: 10/16 A (UK 13A) Power input: switched off 0. 1 W not switched off 0. 1 W Water pressure: at least 0. 05 MPa (0. 5 bar), maximum 1 MPa (10 bar). Inlet rate: minimum 10 litres/minute Water temperature: Preferably cold water; if hot water, depending on type of water inlet hose, max. Capacity: 9–10 place settings (depending on model).
Waste-water connection
1. The required work sequence can be found in the installation instructions. [. . . ]