[. . . ] Digital High Definition Satellite Receiver SRT 7505 Bedienungsanleitung User Manual Abbildung ähnlich Model: Digital HD Satellite Receiver SRT 7505 USB: DC 5 V, 1. 0 A max. 13/18 V 350 mA max. ON/OFF COAXIAL S/PDIF MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES. DOLBY AND THE DOUBLE-D SYMBOL ARE TRADEMARKS OF DOLBY LABORATORIES. SAT IN SAT OUT TV SCART DC 12 V 24 W max. 2. 0 A max. Model: Digital HD Satellite Receiver SRT 7505 USB: DC 5 V, 1. 0 A max. [. . . ] NIT Load HD Austria Senderliste:  Here the “HD Austria Senderliste” can be installed subsequently. In this case, previously installed or available channels are retained and sorted in the “HD Austria Senderliste” accordingly. TV or radio channels which are not included in the “HD Austria Senderliste” are ranked above channel number 4000 or 6000 and can still be edited. When all settings have been made, press OK at the preferred scan method to start this scan process or to quit without scanning. All newly found channels will be stored at the end of the channel list. *Only available if more than one satellite has been setup. Note: N  IT (Network Identification Table): This option will scan data of the NIT table from a satellite and allows you to receive new appeared channels. Please consider that unlike Astra 19. 2 und HOT BIRD 13° some satellites do not offer this function or do not fully support it. 13 Note: W  hen you want to add technical data for a new transponder we recommend verifying it by consulting websites like: www. lyngsat. com or www. kingofsat. net or you can refer to professional journals. 7. 1. 3 System Settings Use the System Settings menu to configure settings for language, audio, video, look and feel of your receiver. Choose a setting with pq and press OK to list the possibilities or use tu to change the value of the highlighted setting. Please also read the displayed instructions for each screen carefully. Language:  Here you can change the language for the On-Screen-Display, use tu to select your preferred language. It affects the menu language of your receiver so all menus and messages will be displayed in the chosen language. Audio Output:  Here you can adjust the settings for your digital audio output. If a device that can decode Dolby® Digital* is connected, use the setting BitStream. For details, see chapter 7. 1. 3. 4 Select Subtitle Language In Start up channel  this menu you can select your start up channel. Select Last watched if your TV shall start with the last viewed channel before the receiver switched off. To switch on with a specific channel, select Fixed Channel by pressing tu. Press pq or P+/P- to scroll in the list and confirm your selection with OK. Banner display time:  Defines the time for displaying the information banner. When returning to viewing mode the receiver informs with a message that it saves your settings. *Dolby Digital Plus and the double-D symbol are registered trademarks of Dolby Laboratories 7. 1. 3. 1 HDMI In this submenu you can set following parameters: TV Ratio  on the kind of your TV set. 16:9 or 4:3, depending Conversion  or Combined, to choose the preferred picture format. Letterbox, PanScan Video Output  Only selectable for Scart Resolution  or 1080p, to adjust the optimum resolution your TV set 576p, 720p, 1080i supports. ON 14 Note: H  DCP (High Definition Content Protection) is set to ON per default as nowadays all TV sets with an HDMI connector support HDCP. [. . . ] When receiver was powered off/disconnected No subscription for the from signal for longer it can take ~1-2h until a selected channel. The remote control does The batteries of the Check whether the batteries are inserted not work remote control are correctly or exhausted, if so replace the batteries not inserted, wrongly in the remote control. Format USB device by receiver in menu Channel The USB storage device Formatted incorrectly. Bigger sized HDD Bigger size HDD or HDDs with more partitions connected. [. . . ]