[. . . ] EFI, Fiery and the Fiery logo are registered trademarks of Electronics For Imaging, Inc. Patent and Trademark Office and/or certain other foreign jurisdictions. The Electronics For Imaging logo, Fiery Scan, Fiery WebScan and Fiery WebTools are trademarks of Electronics For Imaging, Inc. [. . . ] If the PageScope Light logo in the About page is clicked, the web site opens up in the browser.
2
2 Access
2. 2 Entering the Password
To enter administrator mode, type the password into the "Admin Password" box in the upper-left corner of the screen, and then click the [Login] button. If the correct password was entered, you will be logged into the administrator mode and the [Logout] button appears. The PageScope Light settings can only be changed from the administrator mode. Note that the password is case-sensitive, so be sure to type in uppercase and lower-case characters correctly. (The password you should type in here is the same as the administrator password you created with Fiery Controller. ) If a password is entered, that password will be valid in ten minutes.
In the case of Admin mode on PageScope Light, following area become effective. · · · · · · Preference Maintenance (Reset/Initialize) Online Assistance General Setting PCL Setting PostScript Setting
3
3 Screen Configuration
3 Screen Configuration
The configuration of the PageScope Light screen is shown below.
Status display section
The status of the printer and scanner is shown with icons and text.
Ready
Attention
Error
Trouble
4
3 Screen Configuration Tabs
The categories that can be controlled by PageScope Light are displayed. · System · Print · Network Used to control and set the system structure for the Di7210/Di5510 Used for setting the printer controller Used to confirm the network settings
Menus
The information and settings for the selected tab are displayed.
Information and setting details
The details of the selected menu are displayed.
Fiery WebTools Logo (Available for HDD Option)
Clicking this logo displays the settings page for Fiery WebTools, which is built into the printer controller. For details about Fiery WebTools, see the Fiery Printing Guide.
5
4 Description of Each Page
4 Description of Each Page
This section contains descriptions of the information and settings that are displayed when each tab is clicked.
4. 1 System Tab
On the System tab, information concerning the system structure for the Di7210/Di5510 can be checked and set. Checking and setting can be performed with the Summary, Details, Preference, Maintenance and Online Assistance menus.
Summary
A summary of the status and the system structure of the Di7210/ Di5510 is displayed.
Details
The details of the status and the system structure of the Di7210/ Di5510 are displayed. · Input Tray It shows the current status of all the Input Trays installed on the Di7210/Di5510.
6
4 Description of Each Page
· Output Tray It shows the current status of all the Output Trays installed on the Di7210/Di5510. · Hard Disk It shows the status of the hard disk installed on the printer controller.
· ROM Version It shows version of firmware installed on the Di7210/Di5510 and printer controller. · Interface Info It shows information about network interface and local interface. · Consumable It shows the current status of Di7210/Di5510 consumables.
Preference
The environment settings such as the refresh rate time and the system language can be specified.
Maintenance
The printer controller can be reset/initialized and counter values can be checked. · Counter · Reset · Initialize The total number of prints made since the Di7210/ Di5510 was set up can be checked. Clicking the [Restore] button restores the initial factory default settings of the printer controller.
Online Assistance (Available for HDD Option)
Enter information concerning product support and check it when necessary.
7
4 Description of Each Page
4. 2 Print Tab
Use the Print tab for configuring the printer controller settings. Checking and setting can be performed with the Default Set, Test Print, and Font Info menus.
Default Set
You can use this menu to make various printer settings. [. . . ] Print to PostScript Error Specify whether or not a PostScript error is printed.
9
4 Description of Each Page Test Print
It lets you select test print pages and execute a test print operation. You can print Configuration Page, PCL Demo Page, PostScript Demo Page, PCL Font List, and PostScript Font List.
Font Info
It shows a list of fonts built into the printer controller. · PCL Font It shows a list of PCL fonts built into the printer controller.
· PostScript Font (Available for HDD Option) It shows a list of PostScript fonts built into the printer controller.
10
4 Description of Each Page
4. 3 Network Tab
Use the Network tab for confirming the network settings of the printer controller. [. . . ]