[. . . ] Do not unplug and plug in the power cord with a wet hand, as an electrical shock could result. · Do not scratch, abrade, place a heavy object on, heat, twist, bend, pull on, or damage the power cord. Use of a damaged power cord (exposed core wire, broken wire, etc. ) could result in a fire or breakdown. Should any of these conditions be found, immediately turn OFF the power switch, unplug the power cord from the power outlet, and then call your authorized service representative. [. . . ] The inside of this product has areas subject to high temperature, which may cause burns. When checking the inside of the unit for malfunctions such as a paper misfeed, do not touch the locations (around the fusing unit, etc. ) which are indicated by a "CAUTION HOT" caution label. Do not place any objects around the power plug as the power plug may be difficult to pull out when an emergency occurs. P-4 · Always use this product in a well ventilated location. Operating the product in a poorly ventilated room for an extended period of time could injure your health. · Whenever moving this product, be sure to disconnect the power cord and other cables. Failure to do this could damage the cord or cable, resulting in a fire, electrical shock, or breakdown. · When moving this product, always hold it by the locations specified in the User manual or other documents. · Remove the power plug from the outlet more than one time a year and clean the area between the plug terminals. · When unplugging the power cord, be sure to hold onto the plug. Pulling on the power cord could damage the cord, resulting in a fire or electrical shock. P-5 Precautions for Routine · Do not store toner units, PC drum units, and other supplies and consumables in a place subject to direct sunlight and high temperature and humidity, as poor image quality and malfunction could result. · Do not attempt to replace the toner unit and PC drum unit in a place exposed to direct sunlight. 10 Reel Shaft Release Lever. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 6 7 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Maintaining Your Films. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 7. 1 7. 2 ANSI Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Effect of film curl on Film Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 8 9 Daily Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 For Key Operators Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 ii Notes to Operators 1 1 Notes to Operators Information in this booklet refers only to the operation of Roll Film Carrier 22A. For further information regarding Microfilm Scanner's or Reader Printer's, please refer to Microfilm Scanner's or Reader Printer's Operator's Manual. Please read entire manual carefully before operating Roll Film Carrier 22A. 1. 1 The following safety rules should be observed 1. The unit should be kept free from moisture, dirt, dust and exposure to heat and direct sunlight at all times. Failure to do so many cause inferior results or damage the unit, in such case the warranty may be void. WARNING This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. [. . . ] The Odometer has been factory-set to 12. 7 mm (1/2 inch) for one count. 5. 7 Reel Shaft Release Lever After the film has been rewind, the Film Reel Shaft is not pulled back out of the Cartridge Film. Therefore, the Cartridge Film cannot be slid out of Roll Film Carrier. If this should occur, push the Reel Shaft Release Lever toward the rear side of Roll Film Carrier. Reel Shaft Release Lever 10 Installation 6 6 Installation NOTE The Machine Power Switch should be turned OFF before installing the Roll Film Carrier 22A. 1 Align two Guide Rails on the underside of the Roll Film Carrier 22A with the right and left edges of the Carrier Table. Then, slide the Carrier all the way into position along the side edges of the Carrier Table. 2 Plug the Cable Connector of the Carrier into the Socket in the machine dedicated to this Carrier. 11 6 3 Install the Lens Unit all the way into Position. Installation To remove the Carrier from the machine, reverse the order of installation. NOTE The Machine Power Switch should be turned OFF before removing the Roll Film Carrier 22A. 12 Maintaining Your Films 7 7 7. 1 Maintaining Your Films Use the following precautions when handling your own films. ANSI Cartridge 1 Allow a length of 700mm or more for the film leader (the blank section of film at the beginning of a reel of tape) and the trailer (the blank section of film at the end). 700 mm 700 mm or more Trailer Leader 2 Keep the edge of the leader cut straight, especially when the edge is folded, to ensure that the film is unwound smoothly. [. . . ]