[. . . ] NOTE The illustrations in this manual are for explanation purposes only and may differ from the actual unit. Do not share the same power outlet with other equipment to prevent overheating and ï¬re. If the supply cord is damage, it must be replaced by the manufacturer, its service agent or similarly qualiï¬ed persons in order to avoid a hazard. it is strongly recommended to be installed with Earth Leakage Circuit Breaker (ELCB) or Residual Current Device (RCD) to prevent electric shock or ï¬re. [. . . ] Mode Auto Cooling Heating
Air inlet Control Panel (CZ-RWRM1) INDICATOR
POWER TIMER FILTER
(Green) (Orange) (Orange)
POWER TIMER FILTER AUTO
Transmitter Maximum distances: 8m Remote control display Remote Control Preparation
AIR SW ING FA N SP
MODE MODE
AU TO
AU TO
ADDR ESS
EED
1 Press and pull out 2
Insert AAA or R03 batteries (can be used ~ 1 year)
4 Set time 5 Conï¬rm 6 Close the cover
TIMER ON
3 Press CLOCK
OFF/O N
MODE AUTO
AIR S WING
FILTER RE SET FAN SP EED
MANU AL
SELECT
3
CLOCK
TIME R
RC RE SET ADDR ESS SET
SET
CANCEL
4 5
AC RE SET
2 6 1
6
CZ-RWS1 (Heat Pump Model) CZ-RWC1 (Cooling Model)
F567782-OYYF1006-00. Indb 6
7/30/2010 10:27:43 AM
POWER
⢠To turn ON or OFF the unit at a preset time. TO SELECT OPERATION MODE
⢠To cancel ON or OFF timer, press
AUTO mode - For your convenience ⢠Unit selects operation mode according to temperature setting, outdoor and room temperature. HEAT mode - To enjoy warm air ⢠Unit takes a while to warm up. FAN mode - To enables air circulation in the room COOL mode - To enjoy cool air DRY mode - To dehumidify the environment ⢠Unit operates at low fan speed to give a gentle cooling operation. ¢ During soft dry operation, the indoor fan operates at a low fan speed. FAN SPEED
⢠When ON timer is set, the unit may start early before the actual set time in order to achieve the desired temperature on time. ¢ Timer operation is based on the clock set in the remote control and repeats daily once set. ¢ The timer closest to the current time will be activated ï¬rst. ¢ If timer is cancelled manually, you can restore the previous setting by pressing SET . ¢ If the main power is switched off for an hour or more, the clock and timer will need to be set again. TO SELECT FAN SPEED (3 OPTIONS)
AUTO LOW MEDIUM HIGH
OPTIONAL SETTINGS
⢠To avoid unintentional operation, you can assign a different address to each indoor unit. ¢ Press repeatedly to select your desired address setting. Group
ADDRESS
⢠For AUTO, the indoor fan speed is automatically adjusted according to the operation mode. ¢ If the operation mode is set to Fan, the fan speed will be ï¬xed at MEDIUM regardless of the temperature setting. address 1
Address 2
Address 3
⢠By default , ADDRESS 1 is selected. ¢ If the address is set to GROUP, more than one indoor unit can be operated at the same time. RC RESET
SET AC RESET
HINT ⢠Use curtains to screen off sunlight and outdoor heat to reduce power consumption during cool mode. Indb 8
7/30/2010 10:27:44 AM
TO TURN ON OR OFF THE UNIT
⢠To turn ON or OFF the unit at a preset time. 4
SET
3
UP
TO SELECT OPERATION MODE
DOWN
AUTO mode - For your convenience ⢠Unit selects operation mode according to temperature setting, outdoor and room temperature. HEAT mode - To enjoy warm air ⢠Unit takes a while to warm up. FAN mode - To enables air circulation in the room COOL mode - To enjoy cool air DRY mode - To dehumidify the environment ⢠Unit operates at low fan speed to give a gentle cooling operation. [. . . ] Indb 12
7/30/2010 10:27:47 AM
Check the following before calling for servicing. ¢ The unit is forced to operate at cooling mode only in a non-living room, such as a computer room. ¢ Check if the unit has been installed at an incline or the intake grille is not closed properly. ¢ ⢠⢠⢠Make sure the receiver not obstructed. [. . . ]