[. . . ] of Ireland 153
For Example to configurate for Republic of Ireland : dial 153 Advice : If you have bought your product in any of the above countries but want to use it in another one, you can enter the configuration code, according to the above tables, in order to activate the right country settings. Nevertheless, you have to change the telephone line cord adapter according to the country where you want to use it.
www. philips. com/faqs/dect 1
Environment & Safety
Safety information : This equipment is not designed for making emergency calls when the power fails. An alternative should be made available for access to emergency calls. Power requirements : The product requires an electrical supply of 220-240 volts, single phase alternating current, excluding IT installations defined in standard EN 60-950. [. . . ] ** Withheld caller identification
Calling a number from the call log or to scroll through the log Deleting an entry from the call log or to scroll through the log beep to exit
Storing one of the log numbers into your phonebooks or to scroll through the log or beep enter the name
www. philips. com/faqs/dect
7
Using the intercom
This function can only be used with a multi-handset configuration. It allows you to make free internal calls and transfer external calls from one handset to another. long press, enter the handset number (1 to 4) to call the selected handset in idle mode. * If the handset does not belong to the DECT 211 or DECT 215 range, this function may not be available. Intercom & call transfer are only possible with handsets* registered to the same base station.
Fast call transfer During a call in progress you can transfer the call without waiting for the other handset to pick up : All the handsets ring. .
Call transfer to a specific handset During a call in progress you transfer the call to a specific handset : Long press on enter the handset number (1 to 4)
Paging
This feature allows you to locate the handset(s). Once again.
located, press any key on the handset to stop ringing or press
8
www. philips. com/faqs/dect
Using your answerphone
Setting up the answerphone
The answerphone is by default activated with a pre-recorded message and the answer & record mode. (standard quality) - 6 min (high quality) : including personal outgoing message if recorded. Activating the answerphone beep To exit Deactivating the answerphone beep To exit Playing new messages / playing a memo . You can adjust the volume using Playing your old messages or previous or next message Deleting the current message listen to the message Deleting all messages Long press . To exit To exit When playing a message, the date and time of the message are displayed on the handset. icon is
Playing the current outgoing message the outgoing message is played . To exit
www. philips. com/faqs/dect
9
Recording your personal outgoing message speak after the beep * To exit However, if you do so, you will permanently erase the pre-recorded outgoing message. Recording a memo If you want to leave a local message for your family : speak after the beep To exit Selecting the answerphone mode You can select either answering mode only (which plays an outgoing message but does not take messages) or answering & recording mode (which takes messages. ) or to switch between modes To exit answering & recording mode answering only mode
*You will hear the personal outgoing message. This local message (memo) is treated like all other answerphone messages.
Advice: prior to using the answering-only mode, make sure that you have adapted the outgoing message.
Screening the calls while a message is being left
This allows you to listen to any caller leaving a message and to decide whether or not to take the call. Activating call screening From the handset : Deactivating call screening From the handset : Increasing the volume of the call screening During call screening, the volume can be adjusted. When the answerphone is on-line, blinks.
Call interception The recording of the current message is stopped and the call is taken.
10
www. philips. com/faqs/dect
Remote access
This allows you to remotely dial in and access your answerphone via any telephone with a key and tone dialling. or
** :In toll saver mode, if there are new messages the answerphone will answer after 3 rings, and only after 5 rings if there are no new messages. Toll saver is useful for remote access only.
12 www. philips. com/faqs/dect
Changing Remote Access Code (option 4/5) To remotely access your answerphone you need to enter a secret code (4 digits). By default, this code is identical to the RC code written under the base. If you want to change the default code : Enter a personal code and press to validate.
Note : You can delete with your Remote Access Code. If this code has been deleted, the remote-activation of the answerphone is not possible. Choosing the recording quality (option 5/5) You can choose the recording quality of your answerphone. [. . . ] Please contact your PHILIPS dealer in order to purchase new rechargeable battery pack.
-
icon is blinking.
- When the handset is placed - The handset is not placed correctly on the charging unit, no beep is on the base station charging unit. - Battery icon remains empty although the handset has charged for 24 hours. - The product is not properly connected Make sure your product is plugged in. www. philips. com/support 15
- A phonebook entry has not been memorised. [. . . ]