Download your OTHERS SAGEM HILONC user guide or user manual

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

We hope that this user guide will be useful to you.
Once downloaded, you must make sure that the Manual matches the Product for which you intend to use it. You agree to remain entirely responsible for the use you do with the instructions contained in the document, no matter whether damages of losses occur following its use.


Manual abstract: user guide

Detailed instructions for use are in the User's Guide.

[. . . ] Miscellaneous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3. GETTING STARTED WITH THE DEVELOPMENT KIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3. 1. Power Supply not connected. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3. 2. Switch on the Development Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3. 3. [. . . ] 1. 3. Note d'étude / Technical document : URD1­ OTL 5665. 3­ 007 / 72 399 Edition 01 HiLoNC V2 Development Kit Application Note 25/10/2010 - Page 3 / 23 1. SCOPE The object of the document is to describe the interfaces and pin identifications of the Development Kit to test the HiLoNC V2 module in operating mode. 1. 1. Introduction 1. 2. HiLoNC V2 Development Kit Schematic HiLoNC V2 Specification: 5635. 1 005 70086 ed 04 - HiLoNC V2 technical specification. doc HiLoNC V2 Application Note: 5635. 1 007 70230 ed 01 - HiLoNC V2 application note. doc Temperature sensor "ADT7302" specification: ADT7302. pdf Inertial sensor LIS3LV02DQ specification: LIS3LV02DQ. pdf URD1 - OTL 5625. 1 - 010 - N° 69846 - DEMOBOARD MO300 APPLICATION NOTE - ED01. doc Reference 1. 3. ADC CTS DAC DAI DCS DSR DTR ESD GSM GPRS I/O Kbps LED Mbps PCB PSU RF RI RTS RX SIM TX UART Terms and abbreviation Analog to Digital Converter Clear To Send Digital to Analog Converter Digital Audio Interface Digital Communications System Data Set Ready Data Terminal Ready Electrostatic Discharge Global System for Mobile communication General Packet Radio Services Input / Output Kbits per second Light Emitting Diode Mbits per second Printed Circuit Board Power supply unit Radio Frequency Ring Indication Ready To Send Reception Subscriber Identification Module Transmission Universal Asynchronous Receiver and Transmitter Note d'étude / Technical document : URD1­ OTL 5665. 3­ 007 / 72 399 Edition 01 HiLoNC V2 Development Kit Application Note 25/10/2010 - Page 4 / 23 2. PRODUCT OVERVIEW 2. 1. Key features Feature Implementation Direct connection of GSM module via 51 pin socket. or 5V DC Adapter 2A max (with inner "+" and outer "-"). Power regulation for the Development Kit needs (2. 9V and 3. 1V). GSM module interface Power supply Antenna interfaces SIM interface Audios interfaces Serial interfaces Integrated connection SMA connector for GSM uses. Analog audio interfaces with filters and RJ11 connector for connecting a handset, headset or speakerphone. RS-232 interfaces with SubD9 connectors: UART1 ­ full serial interface (all modem status are available). 3 GPIOs. GPIOs Note d'étude / Technical document : URD1­ OTL 5665. 3­ 007 / 72 399 Edition 01 HiLoNC V2 Development Kit Application Note 25/10/2010 - Page 5 / 23 Able to be switched in/out and pull-up/pull-down resistors. ADC interface Protections Physical characteristics One analog input (0 to 1. 8V). ESD and EMC protections on each pin headers and connectors of the Development Kit. Size : 168mm x 118mm x 30mm 2. 2. Functional diagram 5V DC Adapter or Power Supply 3. 7V/2A VBat GSM Antenna Connector Hardware Reset 03 Switches 1/0 selection 03 Switches I/O selection 03 Status LED 03 GPIO's Test Points SIM IC Test points SIM card IC HILONC V2 ON(Pok_IN) UART0 Test Points HILONC V2 SIM Card Test points SIM Card Holder SIM Card Debug SubD9 RS232 Transceiver 2 Status LED SIM card detect To GPIO2 Analog Audio Test points PCM Test points RJ11 Receptade RJ11 Receptade MIC Speaker MIC Speaker SubD9 RS232 Transceiver 8 Status LED UART1 Test Points ADC Test Points Buzzer Tests points PWM Tests points Buzzer VBat BACKUP 2 Status LED Note d'étude / Technical document : URD1­ OTL 5665. 3­ 007 / 72 399 Edition 01 HiLoNC V2 Development Kit Application Note 25/10/2010 - Page 6 / 23 2. 3. Interfaces location 2. 3. 1. Connectors Location MX104 P202 P402 P501 P502 P101 TB801 TB802 P801 P601 Connector's Type 51 pins socket Sub-D 9 Connector RJ11 Receptacle SMA Connector 50 Ohms Laboratory power supply receptacle Ø 4mm Mini DC jack (+ inner, - outer) Ø 2. 5mm Sim card holder Function Module interface UART1 UART0 (Debug) Analog audio Antenna GSM Power supply 1 Power supply 2 SIM Note d'étude / Technical document : URD1­ OTL 5665. 3­ 007 / 72 399 Edition 01 HiLoNC V2 Development Kit Application Note 25/10/2010 - Page 7 / 23 2. 3. 2. Test points Location TB201 TB701 TB702 TB501 TB502 TB503 TB504 TB602 TB601 TB301 TB304 TB305 Connector's Type Pin Headers Pin Headers Pin Headers Pin Headers Pin Headers Pin Headers Pin Headers Pin Headers Pin Headers Function UART1 GPIO PWM Analog audio PCM Analog audio SIM IC (option) SIM CARD POK, ADC0, BACKUP JTAG PORT Note d'étude / Technical document : URD1­ OTL 5665. 3­ 007 / 72 399 Edition 01 HiLoNC V2 Development Kit Application Note 25/10/2010 - Page 8 / 23 2. 3. 3. Switches Location S701 S702 S301 S302 S303 S304 S305 S306 S601 S101 Connector's Type DIP switches DIP switches Push button Switch Inverter Push button Switch Inverter Switch Inverter Switch Inverter Switch Inverter Push button Function GPIO (I/O) INPUT OR OUTPUT GPIO (H/L) HIGH LEVEL OR LOW LEVEL POWER ON BACKUP BATTERY (1) OR 10uf capacitance RESET FOR JTAG FOR JTAG FOR JTAG SIM CARD (1) OR SIM IC (2) (option) Switch OFF the module power supply Note d'étude / Technical document : URD1­ OTL 5665. 3­ 007 / 72 399 Edition 01 HiLoNC V2 Development Kit Application Note 25/10/2010 - Page 9 / 23 2. 3. 4. Jumpers Location TB101 TB102 TB103 TB104 TB401 TB402 TB403 TB404 TB405 TB703 TB704 Connector's Type Pin Headers Pin Headers Pin Headers Pin Headers Pin Headers Pin Headers Pin Headers Pin Headers Pin Headers Pin Headers Pin Headers Function VBAT enable the connection between chip and GPIO enable ANTENNA DETECTION enable ANTENNA DETECTION UART0 test point For PCM For PCM For PCM For PCM BUZZER SIM CARD DETECTION TO GPIO2 Details on jumper function are given in chapter 4. 8: Overview of jumpers. Note d'étude / Technical document : URD1­ OTL 5665. 3­ 007 / 72 399 Edition 01 HiLoNC V2 Development Kit Application Note 25/10/2010 - Page 10 / 23 Note d'étude / Technical document : URD1­ OTL 5665. 3­ 007 / 72 399 Edition 01 HiLoNC V2 Development Kit Application Note 25/10/2010 - Page 11 / 23 2. 3. 5. Miscellaneous Location P301 E301 DS401 LS701 DS801 DS802 Connector's Type Pin Headers Battery (coin) connector LED Buzzer LED LED Function ADC INPUT Backup battery (option) RF indicator Buzzer device (option) Lab PSU indicator DC 5V adapter indicator Note d'étude / Technical document : URD1­ OTL 5665. 3­ 007 / 72 399 Edition 01 HiLoNC V2 Development Kit Application Note 25/10/2010 - Page 12 / 23 3. 3GPP TS 51. 011, 51. 014, 43. 019, 23. 040, 23. 140 3GPP TS 23. 048 3GPP TS 22. 048 ETSI TS 102 221, 102 222 ISO / IEC 7816 The SIM IC is compatible with the ISO 7816-3 IC standard required by the GSM 11. 11 Phase 2+ standard. The SIM IC interface insures the power on (SIMVCC) of the SIM Chip and the communication with it through a data signal (SIMDAT), a clock signal (SIMCLK) and a reset signal (SIMRST). Switch S601 to position "2" to use this SIM. SIM interface 4. 2. 1. SIM IC The SIM Card interface is compatible with the ISO 7816-3 IC card standard required by the GSM 11. 11 Phase 2+ standard. The module also supports Release 99 of the SIM Toolkit recommendation and supports a Fixed Dialling Number directory. The SIM Card interface insures the detection (SIMCD), the power on (SIMVCC) of the SIM Card and the communication with it through a data signal (SIMDAT), a clock signal (SIMCLK) and a reset signal (SIMRST). The jumper TB704 connects the SIM card presence detection to the GPIO2 (IO2) The figure below shows the simplified interface schematic: 4. 2. 2. SIM CARD SIM NC SIMCLK SIMRST SIMVCC 4 3 2 1 10 9 8 7 6 5 NC SIM DATA SIMVCC GND SIM DETECT 4. 3. A V24 interface is provided on external pins of the module with the following signals: RTS/CTS RX/TX DSR DTR Note d'étude / Technical document : URD1­ OTL 5665. 3­ 007 / 72 399 Edition 01 Serial Interface 4. 3. 1. UART 1 HiLoNC V2 Development Kit Application Note 25/10/2010 - Page 16 / 23 DCD RI The signals levels are adapted and connected to the male Sub-D9 connector "UART1" on P202. Eight LEDs are provided on Development Kit to show the status of the UART 1 signal. The figure below shows the simplified interface schematic: 4 signals are provided on external pins of the module with the following functions: RXD2/TXD2 RTS2/CTS2 The signals levels are adapted and connected to the male Sub-D9 connector "UART 0". [. . . ] Jumper not set Power supply the HiLoNC V2 via Q101. Reference The GPIO3 (IO3) is connected to the Reset External hardware reset not controlled by the chip and then the module is able to perform HILONC V2 module. For PCM. Note d'étude / Technical document : URD1­ OTL 5665. 3­ 007 / 72 399 Edition 01 HiLoNC V2 Development Kit Application Note 25/10/2010 - Page 22 / 23 TB404 TB405 TB703 TB704 4. 9. S701 S702 S301 S101 S303 Reference S302 S601 S304 S305 S306 For PCM. Buzzer Disabled The pin SIM card presence detection from The pin SIM card presence detection from the the SIM card holder pins 9 & 10 is connected SIM card holder pins 9 & 10 is not connected to to the GPIO2 (IO2). the GPIO2 (IO2). Overview of Switchers Function Switch on To set up GPIO1 to GPIO3 as an input. [. . . ]

Sponsored Links