DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
We hope that this user guide will be useful to you.
Once downloaded, you must make sure that the Manual matches the Product for which you intend to use it. You agree to remain entirely responsible for the use you do with the instructions contained in the document, no matter whether damages of losses occur following its use.
Manual abstract: user guide
Detailed instructions for use are in the User's Guide.
[. . . ] GK1630T GK1635T GK1640T
Your Black & Decker chainsaw has been designed for pruning and felling trees and cutting logs. Failure to follow the warnings and instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains operated (corded) power tool or battery operated (cordless) power tool. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. [. . . ] Before use, inspect the extension cable for signs of damage, wear and ageing. Electric safety can be further improved by using a high-sensitivity (30 mA/ 30mS) Residual Current Device (RCD). The use of an RCD or other circuit breaker unit does not release the operator of your chainsaw from the safety instructions and safe working practices given in this user manual. Guard against electric shock
The declared vibration emission values stated in the technical data and the declaration of conformity have been measured in accordance with a standard test method provided by EN 60745 and may be used for comparing one tool with another. The declared vibration emission value may also be used in a preliminary assessment of exposure. Take the new chain (6) and soak it in chain oil for at least an hour before using it. We recommend that you use only Black & Decker oil during the lifetime of your chainsaw because mixtures of different oils could lead to the oil becoming degraded, which can drastically shorten the lifetime of the saw chain and create additional risks. Set the front guard/chain brake assembly to the forward position (fig. 9
Place the chain (6) over the guide bar (7) making sure that the saw chain cutters on the upper part of the guide bar (7) face towards the front (fig. U Guide the chain (6) around the guide bar (7) and pull it to create a loop to one side at the rear end of the guide bar (7). U
Allow the control knob to spring back to the „out“ position and rotate further clockwise to tighten the guide bar. Make sure that the front guard/chain brake assembly (4) is in the set (forward) position before refitting (fig. Before fitting the chain cover assembley check that the cam (11) (fig. If necessary, press in and turn the control knob (9) clockwise to rotate the cam into the correct position. U Fit the chain cover by locating the bolt and using the control knob (9) to tighten the chain cover finger tight. U To tension the chain, loosen the control knob one full turn, press in firmly and rotate clockwise. As the bar moves forward make sure that the chain links feed into the guide bar. U Allow the control knob to spring back to the „out“ position and rotate further clockwise to tighten the guide bar. U
Remove the oil cap (3) and fill the reservoir with the recommended chain oil. U Periodically switch off and check the oil level indicator (5); if it is less than a quarter full, disconnect your chainsaw from the mains supply and refill with the correct oil. Switching on
Note: It will not be possible to switch the tool on if the front guard/chain brake assembly is not in the "set" position. Push the lock-off button (2) and then push the on/off switch (1) to start. [. . . ] Technical data Bar length cm Voltage VAC Power input W Chain speed (no load) m/s Max cutting length cm Oil capacity ml Weight kg Safety class Bar length cm Voltage VAC Power input W Chain speed (no load) m/s Max cutting length cm Oil capacity ml Weight kg Safety class
GK1630T Typ. 8 II
Separate collection of used products and packaging allows materials to be recycled and used again. Re-use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials. 9 II
Level of sound pressure according to EN 60745: Sound pressure (LpA) 92 dB(A), uncertainty (K) 3 dB(A) Sound power (LWA) 103 dB(A), uncertainty (K) 3 dB(A) Vibration total values (triax vector sum) according to EN 60745: Vibration emission value (ah) 5 m/s2, uncertainty (K) 1. [. . . ]