User manual ADE OPTIMA G4

[. . . ] Accenta/Optima User Guide ZONE 1 2 3 4 5 6 7 8 Power Day 0 1 6 OMIT 2 7 RESET 3 8 PROG 4 PA !"#$%& Zones Power Attack Tamper Day 1 4 7 2 5 8 0 3 6 9 Reset Chime 5 CHIME 9 SET 0 5 Chime 1 6 Omit 2 7 Reset 3 8 Prog 4 9 Set PA Omit PA Prog Accenta + TA PA DAY POWER Set Accenta/!mini Servicing Organisation (Installer) name: Telephone Number: Date of Installation: Account Number: Honeywell Security Accenta/Optima User Guide Table of Contents Contents Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Alarm System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The screen shows the Day mode: Sunday 14:10 01-Jan Power Day [4-digit code] · Enter your code [0][1][2][3]. Program 1 Set [PROG] Set System Select 1 2 or 3 · Select part-set program [2] or [3]. The exit tone stops. NOTE: There will be no exit beeps if Silent Timed exit mode was programmed. Sunday 01-Jan 14:10 4 Accenta/Optima User Guide LED Keypad: The Day LED should be on. How to Silence an Alarm 12345678 Zones Power Attack Tamper Day · · Enter your code [0][1][2][3]. The exit tone stops and the zone LED's 1 to 3 come on. [0][1][2][3] then [PROG] 12345678 Zones Power Attack Tamper Day · Select part-set program [2] or [3]. The Day LED goes out. [2 or 3] 12345678 Zones NOTE: There will be no exit beeps if Silent Timed exit mode was programmed. Power Attack Tamper Day How to Silence an Alarm and Reset the System If your system goes into alarm then be aware that intruders may be in the premises. The alarm will stop. Enter Your Code [0][1][2][3] 12345678 00100000 TP 0F The screen alternates showing what caused the alarm and prompting for user reset When two or more alarms have occured, the first alarm will have an F below the zone number, Tamper or PA. Subsequent alarms will have a 1 indicating where the alarm has taken place. The system resets and goes into day mode if there are no open Tampers, PA or Fire zones to cause a fault lockout. The system can be reset by the user only if the installer has programmed it to do so. If the message Engineer Restore Required appears on screen then the user will have to contact the installer. · After 30 seconds the set mode display appears. User Restore Press Reset [RESET] Restored by User Sunday 01-Jan 14:10 5 How to Omit Zones LED Keypad: · Enter your code [0][1][2][3]. The alarm will stop, and the Zone, Tamper (TA) or Attack (PA) LED's will come on to show the cause of the alarm. Accenta/Optima User Guide [0][1][2][3] 12345678 Zones Power Attack Tamper Day NOTE: When 2 or more LED's are on, the flashing indicator shows the first alarm, and the steady indicators show the second and subsequent alarms. This also means that you need to wait 30 seconds for the system to set. You can reduce this time to just five seconds by carrying out a Quick Set. · Press [SET] to Quick Set the system and the exit beep tone will change to a more rapid tone. The system will set in five seconds, and the exit tone will stop. Single Key Setting If enabled by the engineer, the setting process can be started by pressing Set, rather than entering a user code. 7 How to Set Up Chime Mode Accenta/Optima User Guide How to Set Up Chime Mode Chime is a low security facility for use when the system is unset. It is particularly useful in a shop to warn of customers presence, or in a house to warn when a back door has been opened. When a Chime zone detects movement the system will produce a brief two­tone sound, and the Zone LED will come on. The screen will show the first zone that is already set up for Chime (possibly none). [CHIME] Zn: Descriptor Chime: NO [Number] Zn: Descriptor Chime: YES · When you have finished using the Chime mode press [RESET] or wait a few seconds for the display screen to show Day mode. [RESET] Sunday NOTE: Zn = Zone number 01-Jan 14:10 LED Keypad: · The system should be in Day mode (System Unset). The zone LED's will come on to show those zones that are already set up for Chime (possibly none). [CHIME] 12345678 Zones Power Attack Tamper Day · Press the zone [number] to toggle it in and out of chime. [Number] 12345678 Zones Power Attack Tamper Day · When you have finished using the Chime mode press [RESET] or wait a few seconds. [. . . ] [PROG] then [0][1][2][3] 12345678 Zones · · · · Press [PROG] and then enter your code [0][1][2][3]. The Day LED goes off and the Tamper (TA) LED comes on to indicate that you are in Programming mode. Press [1 to 8] for the desired event or [CHIME] to go through events in sequence. Power Attack Tamper Day [CHIME] 12345678 Zones Power Attack Tamper Day · Press [RESET] twice to leave the menu. 1 2 [RESET] 3 4 5 6 7 8 How to Test Your Alarm system You should check that your alarm system still works correctly by periodically carrying out the alarm system tests described here. How to Test the Bell, Strobe and Internal Sounder This function tests the alarm function of the Bell, Strobe or Internal Sounder. Pressing the [RESET] button turns off all outputs and leaves the function. [. . . ]