User manual AEG-ELECTROLUX EFCR953U

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual AEG-ELECTROLUX EFCR953U. We hope that this AEG-ELECTROLUX EFCR953U user guide will be useful to you.


AEG-ELECTROLUX EFCR953U : Download the complete user guide (439 Ko)

You may also download the following manuals related to this product:

   AEG-ELECTROLUX EFCR953U (439 ko)
   AEG-ELECTROLUX EFCR953U (717 ko)
   AEG-ELECTROLUX EFCR953U (722 ko)

Manual abstract: user guide AEG-ELECTROLUX EFCR953U

Detailed instructions for use are in the User's Guide.

[. . . ] 4. 5 - Fix the telescopic metal frame. 4. 1 - Fixing the wall brackets (and splashback) Ref. 2 a-b 1 - Draw a vertical line on the wall from the centre of the cooking appliance up to the ceiling, using a marking pen. 1: a - put the bracket l to the wall, aligning its marked centre across the vertical line, ensuring that the distance between the centres of the holes and the cooking area is as follows : 1 - when the splashback is to be installed: d=270mm+H mm, where H is the height of the visible part of the splashback. As the splashback can be of different heights, the correct H figure can only be obtained by measuring the actual height of the splashback to be fitted. [. . . ] 5 - Pilot drill all the hole positions as marked on the wall using a 8mm drill. Fix the wall brackets 1 - 2 3 using the 8mm rawl plugs and screws supplied. When the splashback F is to be fitted, the distance between the cooker hood and the cooking appliance will be determined by the height of the splashback. If the splashback is to be fixed to the wall using both the upper and lower fixing points, care must be taken to ensure that the splashback if fitted at the correct height before placing in position the base cabinet and worktop. Being a rather complicated operation, the fixing of the splashback should be carried out by a qualified or competent person, knowing all the final dimensions of the furniture. If the splashback is to be fixed through only the upper part, proceed as follows : a - Put the splashback on the worktop as shown on Fig. 2; then hold it against the wall ensuring that it is correctly positioned on the worktop. b - Mark on the wall the two hole positions which appear on the upper part of the splashback. c - Pilot drill the hole positions using a 8mm drill and fix the splashback using the 8mm rawl plugs and screws supplied. d - The installer should ensure that the lower part of the splashback is adequately fixed. 4. 2 - Fitting the canopy (Fig. 3). 1 - Rotate halfway the two screws R positioned on the hanging lugs of the canopy. 9). Part 2a OPERATION AND MAINTENANCE INSTRUCTIONS 1SAFETY WARNINGS. It is most important that all the warnings shown in paragr. Moreover pay special attention to the following warnings during the use and maintenance of the cooker hood. 1. 1 - The grease filters and the charcoal filter should be cleaned or replaced as recommended by the manufacturer or more frequently if the hood is used consistently (over 4 hours per day). 1. 2 - When using a gas hob in conjunction with the cooker hood, never leave the burners uncovered while the hood is in use; when removing the pans either turn the hob off or keep the flame to a minimum if it is only for a few minutes and under supervision. 1. 3 - Always ensure that the flame does not overflow from under the pans; this will save energy and will avoid a dangerous concentration of heat. 1. 4 - Do not use the appliance in any incorrect way: this hood has been designed only to reduce the smells of cooking in the kitchen. 22. l - OPERATION. The cooker hood functions are located in a concealed control panel on the right hand side of the canopy, behind the front trim. To gain access to the control panel apply slight pressure to the control panel back and release. To relocate the control panel in its concealed position just push it back upwards. 11): - the switch L, marked with the lamp symbol, controls the worktop illumination; - the switch M, marked with the fan symbol, controls the power to the fan motor (0-1); - the switch V, marked 1-2-3, controls the fan speed: - position 1: low speed, should be selected when simmering or using only one pan; the noise level is kept to the minimum. This speed offers the best ratio between air capacity and noise level. - position 3: top speed, should be selected when frying or cooking food with strong odours, even for a long period. 2. 2 - 3- MAINTENANCE. Regular maintenance and cleaning will ensure good performance and reliability, while extending the working life of the hood. [. . . ] The filter panels should be refitted with bolt side facing downwards. 3. 2 - Thin synthetic filter. On certain models the metal grease filters are replaced with a lower grille panel containing a paper filter with saturation indicators. a - Cleaning: The paper filter visible through the perforated metal grease filter tray cannot be washed and should be replaced when the white areas between the violet dots turn brown. b - Replacement: To remove the filter for subsequent replacement first open the metal grille panel (Fig. To remove the metal grille panel slide the right hand side of the panel forward until the hinge pin comes away from the recess in the side casing (Fig. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE AEG-ELECTROLUX EFCR953U




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual AEG-ELECTROLUX EFCR953U will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.