User manual AEG-ELECTROLUX EKC60050X

[. . . ] - This household appliance has been designed for cooking and it must therefore be used for this purpose only. dEAR CUSTOMER , · Carefully read these instructions before using the appliance and keep them for future consultation. If it is missing, ask the retailer for it indicating purchasing date, model, and data plate number which are printed on the data nameplate identifing the appliance ( fig. Keep the part destined to you, and in case of necessity, show it to the Technical Service together with the receipt bill. [. . . ] Assemble everything carefully in the opposite direction check the connection seal by means of soapy water. TAPS REPLACEMENT Act as follows: switch the appliance off, and close the general tap open the work-top and disassemble also the control panel as described on the previous paragraph. Note: Every time the tap is replaced, it is necessary to replace the seal gasket too check the connection seal by means of soapy water (see picture). It is possible to select the desired temperature into the oven by turning clockwise the thermostat knob and depending on the models, one or more functions: Oven off Oven light 60 ÷ Use of the oven Note: ovens with separate thermostat and commutator. When the functions are used, place the thermostat knob between 180 ÷ 200°C as maximum temperature. ATTENTION: The temperature shown on the control panel corresponds to the temperature in the oven centre only when the functions selected are or . When you turn the control knob to this position, the light will be on for all the following operations. The plug used for mains supply connection should be easy to get at, once the appliance is in position. Important: position the mains supply cable so that it is never subjected to a temperature which is more than 50°C above ambient temperature. The electrical safety of the appliance can only be guaranteed when it has been correctly connected to an efficient earthed power supply, as laid down in the regulations for electrical safety. Important: the manufacturer cannot be held responsible for any damage to persons or objects due to the lack of an earth connection. For the indispensable entry of fresh air into the room there must be a similar 100 cm2 opening directly to the outside, situated at a height near floor level so that it is not blocked either inside or outside the wall and so as not to cause disturbances to correct burners combustion and to the regular removal of spent air and with a difference of height with respect to the outlet opening of at least 180 cm. Remember that the quantity of air necessary for combustion must never be less than 2m3/h for each kW of power (see total power in kW on the appliance data plate fig. When there are other gas appliances in the same room, or when natural direct ventilation is not possible and natural indirect or forced ventilation must be installed, contact a qualified specialist who will install and make the ventilation system, scrupulously observing the regulations contained in the standards in force. The openings must be so positioned that there are no draughts of air which cannot be tolerated by the occupants. Moreover to eliminate combustion products, it is forbidden to use flues already used by other appliances. 3 ) by flexible tube in stainless steel with continuing wall, with mechanical connection in accordance with rules. 2 WARNINGS Concerning rubber flexible tubes, we remember you: 1 - to avoid the tube to be narrowed or crushed 2 - do not submit it to traction or torsion efforts 3 - to avoid contact with sharp edges, etc. 4 - to avoid contact with parts reaching temperatures over 70°C the ambient temperature 5 - to ensure that they can be checked for all their length. Warning: Some models are designed for the grill to be used with the oven door completely closed. - Thread the chicken or the cubes of meat for roasting on the spit L , ensuring that it is gripped safely between the two forks F and balancing it properly to avoid unnecessary strain on the trasmission R (fig 3). - Put the spit on the support G, after having introduced its opposite end in the socket P of the transmission R (fig 3) - Put the support G completely into the oven so that the bar I goes into the socket H of the turnspit motor M (fig 3A). [. . . ] Sound signal The sound signal starts at the end of a programme or of the minutes counter function and it lasts for 15 minutes. Start programme and check The programme starts 4 seconds after it has been set. The programme can be checked at any time by pressing the corresponding button. Setting error A setting error is made if the time of day on the clock falls within the cooking start and end times. [. . . ]