User manual AEG-ELECTROLUX ESF6236

[. . . ] . 3 Operating Instructions 1 Safety Prior to using for the first time · Follow the "Instructions for installation and connection". Correct use · The dishwasher is only intended for washing domestic dishes. · Additions or modifications to the dishwasher are not permitted. · Use only special salt, detergent and rinse aid suitable for domestic dishwashers. This could cause an explosion. Child safety · Keep packaging away from children. [. . . ] Before the start of the dishwashing cycle put 3in1 detergent in the detergent dispenser. If you do not want to use 3in1 products any more If you want to stop using 3in1 products, please do the following: · Fill up the dispensers for salt and rinse aid again. · Switch the water softener to the highest setting and perform up to three normal cycles without loading any dishes. · Then set the water softener to the water hardness in your area. If you want to use 4in1 products When using "4 in 1" detergents that integrate also anti- glass corrosion agent into "3 in 1" formula, please follow the same indication as given for "3 in 1" detergents. 17 Selecting the dishwashing cycle (Cycle Table) Programme sequence Intermediate rinse Dishwashing cycle1) Suitable for: Type of soiling Pre-wash Consumption values2) Length (minutes) Energy (kWh) 1, 85 - 2, 05 1, 10 - 1, 60 0, 8 0, 95 - 1, 05 0, 9 * Dinner service and cookware heavily soiled, dried-on food remains, in particular protein and starch normally soiled, dried-on food remains just used, lightly to normally soiled 120 - 130 · · · · 100 - 120 *3) Dinner service and cookware Dishes, excluding saucepans Dinner service and cookware, temperaturesensitive crockery Dessert dishes and coffee service, delicate glassware · · · · - · - · - 30 130 - 160 5) normally soiled · · · · · 73 lightly soiled - · · · 1) In all dishwasher programmes with a *, during the final rinse the temperature is raised to 68° for 10 minutes to hygienically clean e. g. 2) The consumption values were obtained under standardised conditions. 3) When using this cycle the degree of water clouding determines the amount of soiling on the dishes. The length of the cycle and water and energy consumption can vary greatly ­ depending upon the load and how dirty the dishes are. Depending upon the soiling, the temperature of the water will be automatically adjusted to between 50°C and 65°C. 5) Test programme for Test Institutes 18 14 2x 13 - 15 9 4) 12 - 24 1 to 2x 22 - 24 2x Water (litres) Main wash Final rinse Drying Selecting a programme When your dishes look like this, select: an intensive programme. a normal or energy-saving programme. a short programme (e. g. The remaining time expected for the cycle will be shown in the multi-display. The selected cycle will begin after approximately 3 seconds. Setting the Delay Timer a dishwashing cycle for between 1 and 19 hours. 1. Press the Delay Timer button repeatedly until the multi-display shows the desired time delay, for example 12h, if the cycle is to start in 12 hours. When the fault is remedied, press the button for the cycle that has started. With other fault codes ("Å " followed by a number): ­ Abort the dishwashing cycle. If the fault is displayed again, please contact the Customer Care Department and inform them of the fault code. Malfunction Possible cause Remedy Water tap is blocked with limescale Check the water tap and have it reor faulty. The filter (where present) in the threaded hose fitting on the tap is blocked. Cancel the dishwashing cycle (see chapter: Starting a dishwashing cycle), clean filters (see chapter: Cleaning the filters), then start the dishwashing cycle again. First shut off the water tap, then switch off the appliance and contact the Customer Care Department. Plug in mains plug. The cycle indicator for the selected dishwashing cycle is flashing: fault code Å 10 is displayed in the multi-display: Filters in the base of the dishwash(Problems with water inlet) er compartment are blocked. Water inlet hose has not been correctly positioned. ed dishwashing cycle is flashing, fault code Å 20 is displayed in the Water drain hose multi-display. (Problems with water drainage) Fault code Å 30 is displayed in the The anti-flood system has been multi-display. The cycle is not starting. A fuse in the house's wiring system Replace fuse. [. . . ] · To compensate for unevenness in the floor and to match the height of the appliance to that of surrounding units, extend the threaded feet using a screwdriver. · Adjust the rear feet of the appliance using a cordless screwdriver from the front of the appliance. (See installation instructions. ) · The drain hose, inlet hose and mains cable must be laid so that they are able to move freely within the plinth area, and so that they are not kinked or crushed when the dishwasher is in position. · The dishwasher must also be screwed tightly to the work surface or to the adjoining units. [. . . ]