User manual AEG-ELECTROLUX EWT136451W

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual AEG-ELECTROLUX EWT136451W. We hope that this AEG-ELECTROLUX EWT136451W user guide will be useful to you.


AEG-ELECTROLUX EWT136451W : Download the complete user guide (11887 Ko)

You may also download the following manuals related to this product:

   AEG-ELECTROLUX EWT136451W (6397 ko)
   AEG-ELECTROLUX EWT136451W (11913 ko)

Manual abstract: user guide AEG-ELECTROLUX EWT136451W

Detailed instructions for use are in the User's Guide.

[. . . ] Ensure that, after installation, the power cable is not trapped under the appliance. If the appliance is installed on carpeted floor, ensure that the carpet does not obstruct any ventilation ducts located at the base of the appliance. The appliance must be equipped with an earthed power plug which conforms to regulations. [. . . ] Permanent : Hold down the "Prewash" and "Delay Start" pushbuttons for a few seconds. "DELAY START" This option allows you to delay the start of a wash programme by 30, 60, 90, 2 hours to 20 hours. You can change or cancel the delayed start time at any time before you press the Load the washing, close the drum and the lid of your washing machine. Before closing the lid of your appliance, ensure that the drum is properly closed : · When the two shutters are closed, · locking button A released. PROPORTIONING OF DETERGENTS Pour the amount of washing into the washand prewash compartments if ing you have selected the "prewash" option. If you turn the programme selector to another programme while a cycle is in progress, the appliance will ignore the new selected programme. If you have already pressed the "Start/ pushbutton and you want to Pause" change or cancel the delayed start, proceed as follows : · To cancel the delayed start and start the cycle immediately, press "Start/Pause" and then "Delay start" . To change the timer delay period, you position must go through the "Stop" and reprogramme your cycle. If you need to open it, you must first pause the appliance by pressing the pushbutton. After closing "Start/Pause" the lid again, press the "Start/Pause" pushbutton. Using the "Time Manager" The level of soiling of the laundry is also indicated. It is normal for the programme selector to remain stationary during the cycle. WARMING UP During the cycle, the symbol comes on when the appliance is reaching the right temperature. INTERRUPTING A PROGRAMME Adding washing is on, you When the "Add washing" light can add washing by proceeding as follows. Pushbutton : Press the "Start/Pause" the corresponding light will flash green while the appliance is paused. The lid can only be opened around 2 minutes after the washing machine has come to a stop. press the pushbutton again to con"Start/Pause" tinue the programme. Modifying the programme in progress Before making any changes to the current programme, you need to pause the washing machine by pressing the "Start/Pause" pushbutton. [. . . ] The water inlet filters are dirty, the power or water supply has been cut off, the motor overheating detector has been activated, the water inlet temperature is lower than usual, the foam detection security system has been activated (too much detergent) and the washing machine has begun draining the foam, · The out of balance detector has been activated: an extra phase has been added to distribute washing more evenly in the drum. The "immediate opening"1) light is not lit, · The temperature inside the drum is too high, · The wash cycle is much too long : The washing machine stops during a wash cycle : The lid doesn't open at the end of the cycle : The E40 error code appears in the display2) and the "Start/Pause" pushbutton flashes red 3) : Electrolux 23 Problems The E20 error code appears in the display2)and the "Start/Pause" pushbutton flashes red3): The E10 error code appears in the display2) and the "Start/Pause" pushbutton flashes red3): The EF0 error code appears in the display2) and the "Start/Pause" pushbutton flashes red3): Softener runs directly into the drum when filling the dispenser box: · The anti-flooding security system has been activated, please proceed as follows : - close the water inlet tap, - empty the appliance for 2 minutes before unplugging, - call the after-sales service. 2) On some models, the auditable signals can sound 3) After solving any problems, press "Start/Pause" pushbutton to restart the interrupted programme. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE AEG-ELECTROLUX EWT136451W




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual AEG-ELECTROLUX EWT136451W will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.