User manual AEG-ELECTROLUX F50671

[. . . ] To ensure optimal and regular performance of your appliance please read this instruction manual carefully. It will enable you to navigate all processes perfect ly and most efficiently. To refer to this manual any time you need to, we recommend you to keep it in a safe place. We wish you much joy with your new appliance. 1 3 2 The following symbols are used in this user manual: Important information concerning your personal safety and information on how to avoid damaging the appliance. [. . . ] For this reason, some detergent tablets do not attain their full cleaning power dur ing short cycles. Therefore please use dishwashing cycles with pre wash when using detergent tablets. 20 In daily use Using 3in1 detergents These products are detergents with a combined cleaning, rinsing and salt func tion. When the 3in1 function is activated, the addition of special salt and rinse aid from the respective dispenser is pre vented. If the salt and rinse aid dispensers are empty, this is not indicated. If you want to use 3in1 detergents, check whether these detergents are suitable for your water hardness. (Follow manufacturer's instructions!) If your water hardness is higher than that recommended by the manufacturer but you would nevertheless like to use 3in1 detergent, proceed as follows: With the 3in1 function selected, set the water softener one hardness setting lower than when rinsing without 3in1 detergent. The dishwasher remembers the two different settings of the degree of hardness for rinsing with and without 3in1 function. 3 In daily use 21 Activation/deactivation of the 3 in 1 function Press simultaneously the two buttons positioned over the writing Multitab, un til the "Multitab function "indicator light illuminates. To deactivate the function press the same buttons again until the indicator light corresponding to the "Multitab" symbol turns off. 3 As the rinse aid inflow is automatically switched off when the 3in1 function is activated, it may come about because of the different quality standards in the 3in1 detergent, that the dishes do not dry sufficiently. If this happens, proceed as follows (see section "Adding rinse aid"): Fill up the dispenser (if this is empty) with rinse aid. If you do not want to use 3in1 products any more If you want to stop using 3in1 products, please do the following: Deactivate the 3in1 function. Switch the water softener to the highest setting and perform up to three nor mal cycles without loading any dishes. Occasionally check the internal dispensers, door seal and water inlet filter (if fitted) for dirt and clean them, if necessary. Cleaning the filters 3 The filters must be regularly checked and cleaned. Turn the handle about of a turn anticlock wise (A) and remove the filter system (B). 3. Grasp the grip hole on the fine filter (1) and remove it from the micro filter (2). Clean all filters thoroughly under running water. Care and cleaning 5. Remove the flat filter (3) from the base of the washing compartment and clean both surfaces thoroughly. Insert the filter system in place and lock it by turning the handle clockwise as far as it will go. Ensure that the flat filter does not pro trude above the base of the washing com partment. Under no circumstances may the dishwasher be used without its filters. 27 1 28 What to do if. . . What to do if. . . Remedying small malfunctions Before you call the Customer Care Department, please check whether you cannot remedy the fault yourself with the help of the following fault ta ble or whether it is caused by faulty, electrical connections and/or faulty water con nections. In these cases the engineer must make you liable for the costs of the Customer Service intervention even during the warranty period. If while the appliance is operating indicators on the control panel flash or are lit up as described in the following table, please consult this to find out how to remedy the fault. After remedying the fault that is flashing in the first or second rhythm in the programme progress display, press the button for the dishwashing cycle that had already started. [. . . ] The inlet hose is fitted with either a plastic or a metal nut: Only tighten the nut hand tight. (Make sure that the tap is not drip ping. ) So that access to the tap in the kitchen is not restricted by the use of the dish washer, we recommend installing an additional tap, or fitting a T branch to the existing tap. The electrical cable for the safety valve is in the double walled water inlet hose and is live. Therefore do not immerse the water inlet hose or the safety valve in water. Water drainage 1 Drain hose The drain hose must not be kinked, crushed or entangled. [. . . ]