User manual AEG-ELECTROLUX F50777

[. . . ] 152950 34/0en 15-02-2006 9:22 Pagina 1 FAVORIT 50777 Dishwasher Instruction book PERFEKT IN FORM UND FUNKTION 152950 34/0en 15-02-2006 9:22 Pagina 2 Dear customer, Please read this User Information carefully and keep it to refer to at a later date. The following symbols are used in the text: Safety instructions Warning!Useful tips and hints Environmental information Your dishwasher has the new washing system "IMPULSE WASHING". With this dishwashing system the motor speed and spray pressure are varied during the wash cycle to achieve better cleaning of the dishes. [. . . ] To compensate the lower temperature, the duration of washing and drying have been extended. (2) The consumption values are intended as a guide and depends on the pressure and the temperature of the water and also by the variations of the power supply. "AUTOMATIC" washing programme During the "AUTOMATIC" washing programme the amount of soil on the dishes is determined by how cloudy the water is. If the appliance is partially loaded and the dishes lightly soiled, the "prewash", "main wash", and "rinse" phases of the programme are shorter and the water consumption level is lower. If the appliance is fully loaded and the dishes heavily soiled, the "prewash"", main wash", and "rinse" phases of the programme are longer and the water consumption level is higher. For this reason the programme duration, water and energy consumption levels can vary within the stated range for AUTOMATIC programme (see "Washing programmes chart"). During the "AUTOMATIC" programme the temperature of the main wash water is also automatically adjusted between 50°C and 65°C depending on the amount of soil on the dishes. Water (litres) 9 4 Intermediate Final rinse Drying 27 152950 34/0en 15-02-2006 9:23 Pagina 28 Operating instructions Starting a washing programme 1. Check that the baskets have been loaded correctly and that the spray arms can rotate freely 2. Press the On/Off button The On/Off indicator light illuminates. 5. Setting and starting the programme To select a programme, press the button of the programme you wish to select, (see "Washing programmes" chart), the indicator light of the button illuminates and in the digital display will appear, flashing, the running time of the programme that has been set (in minutes). After about 3 seconds from the last pressure of a button the programme starts automatically. In the digital display the running time of the programme is no longer flashing. Setting and starting the programme with the delay start The setting of the delay start occurs before selecting the programme Press the delay start button until the flashing number of the hours for the delay start will appear in the digital display (from 1h to 19h). Select a washing programme (see "Washing programmes" chart). In the digital display will appear, for a moment, the running time of the programme and then again appears the selected delay start time. As soon as the number of hours is displayed without flashing, the countdown for the delay start is active. The countdown will decrease with steps of 1 hour. 28 152950 34/0en 15-02-2006 9:23 Pagina 29 Operating instructions The opening of the door during the countdown will not modify the delay start. Once the delay start has elapsed the programme will start automatically. Note: it is possible to select a washing programme and the delay start also with the door slightly opened. In this case the start of the programme or of the countdown will occur after the closure of the door. To interrupt or cancel a washing programme in progress Interrupt or cancel a washing programme in progress ONLY if it's absolutely necessary Attention!Open the door carefully. Interrupt a washing programme in progress a) Open the dishwasher door; the programme will stop. Close the door; the programme will start from the point at which it was interrupted. b) Press the On/Off button, in this case all the indicator lights turn off. [. . . ] This appliance complies with the applicable plumbing regulations. 43 152950 34/0en 15-02-2006 9:23 Pagina 44 Installation instructions Water inlet hose with safety valve After connecting the double-walled water inlet hose, the safety valve is next to the tap. Therefore the water inlet hose is only under pressure while the water is running. If the water inlet hose starts to leak during this operation, the safety valve cuts off the running water. Please take care when installing the water inlet hose: - The electrical cable for the safety valve is in the double-walled water inlet hose. - If water inlet hose or the safety valve is damaged, remove the mains plug immediately. [. . . ]