User manual AEG-ELECTROLUX LAVW1230-W

[. . . ] LAVAMAT W 1230 Washing Machine User information Dear Customer, Please read this user information carefully. Pay particular attention to the section "Safety" on the first Info pages. Please keep this user information in a safe place for later reference. Pass it on to any future owners of the unit. 1 The warning triangle and /or signal words (Warning!, Caution!, Important!) emphasise information which is important for your safety or for the unit's functional reliability. [. . . ] Adjust the feet according to the instructions for installation and connection. There is very little washing in This does not impair the the drum (e. g. The water could not be completely pumped out before spinning because the drain hose is bent or the drain pump is blocked. Check along the drain hose and remove any kinks present, or clean the drain pump and, if necessary, remove foreign bodies from the pump housing. The screw connection on the Tighten the inlet hose screw inlet hose is leaky. Close cover correctly. Interrupt the programme and remove washing from Washing is stuck in the door. Seal the emergency drain hose correctly (see section Emergency drain hose is not "Carrying out an Emergency correctly sealed or is leaking. Cancel RINSE HOLD. The washing machine does not spin; there is water in the drum. Release SOAKING button Soaking programme has fin(main wash programme will ished. follow). 31 Operating Instructions Problem Softener has not been flushed into machine; drawer æ for care agent is filled with water. Possible Cause Remedy The softener insert has not Wash the washing powder been correctly positioned indrawer and position the sofside the care agent comparttener insert firmly. Follow instructions for the maximum filling quantity (see Programme Tables). The washing was not able to Always load the drum as ful be distributed evenly in the as possible with a combinadrum prior to spinning. Remove the bend. Contact customer service; a Maximum pump head (outlet retrofit kit is available as a head 1m from unit's floor special accessory for pump Washing has not been surface) exceeded. Residual water is still visible in Switch off the unit and pull the drum. Filter in the screw connection of the inlet hose on the water valve or on the unit is blocked. The cause is probably a washing powder/liquid with a high silicate content. No negative influence on the rinse results; perhaps use liquid washing agent. The rinsing water is murky. Door cannot be opened. Door is locked for safety rea- Wait for 1 or 2 minutes after sons. the end of the programme. 32 Operating Instructions If the washing results are not satisfactory If the washing has turned grey and if limescale is deposited in the drum, then · Too little detergent was used. · If multi-component detergents are used, the individual components were not used in the correct ratio. If there are still grey spots on the washing, · Washing soiled with ointments, grease or oils was washed with too little detergent. · A frequent cause is that softener - particularly that in concentrated form - has reached the washing. If at the end of the last rinse foam is still visible · Modern detergents can also cause foam in the last rinse. If there are white remnants on the washing · These are insoluble components of modern detergents. In future, perhaps you should turn the washing inside out before washing it. [. . . ] Terlaton Street 42/44 1011 Riga Tel. : 371 2 297821 Fax: 371 2 821286 Lthuania Electrolux Lthuania Verkui 29 2600 Vilnus Tel. : 372 272 3326 Fax: 372 272 3366 Poland Electrolux Poland Sp. Domaniewska 41 02-034 Warszawa tel. : 022 874 33 33 fax: 022 874 33 00 Russia Electrolux Russia Ltd. 16 Olympiysky prospekt 129090 Moscow Tel. : (095) 937 7837 Fax: (095) 926 5513 48 Warranty conditions / Customer service centres Israel Electricity & Electronic Services-Evis LTD. Raanana, Industrial area 43654 Tel: 972-9-7448118 Fax: 972-9-7603618 e-mail:evis@evis. co. il Malaysia Arzbergh Engineering No. [. . . ]