User manual AEG-ELECTROLUX RM120

[. . . ] LU4 9QQ Tel: LUTON 53255 INSTRUCTIONS FOR INSTALLATION OF REFRIGERATOR MODEL RM12O (BOTTLED GAS AND 12V) IN CARAVANS AND MOBILE HOMES 1. , INTRODUCTION These instructions are important and must be followed closely. Before starting to install the refrigerator, read this leaflet carefully in order to obtain a thorough understanding of what is required. When operating, heat is emitted from parts of the cooling unit at the rear and this has to be carried away by air circulating freely over the back of the refrigerator. To ensure sufficient air circulation for satisfactory operation, it is essential that the clearances called for in this instruction are not reduced in any way otherwise cooling performance will be impaired and consumption increased. [. . . ] For future reference, any changes made should be recorded on or beside the data label Pressure From Gas Bottle Regulator (water gauge) 11" (280mm) 11" to 14" (280 to 370mm) 20" (500mm) (Usually Germany and Austria) Type of Gas Type Of Burner Size of Burner Jet Size of Thermostat By Pass Screw 1 *BUTANE PROPANE With two aeration holes With one aeration hole 27 (Part No. 34191312) 2 PROPANE *eg Calor Gas, Caravangas or Camping Gaz 2 8 . FREE-STANDING INSTALLATIONS If the refrigerator is to be used as a free-standing model, a vertical free space of at least 75 mm (3") must be left over the top so that the air circulating over the cooling unit at the back can emerge unhindered. The flue kit for venting the flue gases to the outside air must be fitted, - see item 11. The refrigerator must be secured by some means to prevent it moving and causing possible damage to the pipe line or its connections. A suggested method of securing is by means of metal brackets about 20 mm (%") wide, (which should be made to suit the particular installation), screwed to the rear top corners of the refrigerator casing and to the wall of the caravan (fig. It is not advisable to fix by means of screws or bolts through the holes in the feet as this could make subsequent removal for servicing, difficult or time consuming. 9 . BUILDING-IN When the refrigerator is built-in, adequate space must be left under, over and behind it to allow a sufficient circulation of air over the cooling unit at the back for satisfactory operation. However, where space limitations do not permit the upper ventilator to be fitted at the front, the alternative arrangements shown in figs. 5 & 6 may be adopted and the height of the recess reduced accordingly. A work-surface can then be fitted over the top front of the refrigerator, but it must not over-hang the door where it would interfere with the operation of the travel catch. 3 Securing in the Recess The refrigerator must be secured in the recess to prevent movement. The method suggested in item 8 may be adopted, or wooden battens may be screwed to the sides of the recess, bearing down on the top of the cabinet from front to back, to hold it firmly as shown at A, fig. Whichever method is used, it must be possible to remove the refrigerator easily for subsequent servicing purposes. The brackets or battens must be in a position where they will not restrict the air circulation over the cooling unit; they must not be positioned across the cabinet over the ventilation openings in the top rear of the casing, or over the fins of the condenser protruding from the cooling unit at the rear, otherwise air-flow will be impaired and performance affected. Fitting the Upper Ventilator To fit the upper ventilator, screw a block of wood approx. 25mm (1") square x 66mm (2 5/8 ") long, to each side of the recess, 16mm (5/8") from the front edge, as shown at B, fig. Heat-resistant rubber flap The flue top (G) is in the form of a lazy "T" and incorporates an air-break to minimise the possibility of flame extinction due to draughts. There is a choice of two positions for fitting the flue venting kit, thus varying the height of the outlet in relation to the top of the refrigerator as shown in figs. The position best suited for each particular installation should be decided 4 upon at this stage taking into account structural framework within the caravan wall, the contour of the wall, and the location of windows, beadings, etc. 10, the flue top (G) is fitted on the end of the aluminium flue pipe of the refrigerator, above the top of the cabinet. To give sufficient clearance for the flue components when so used, an additional vertical clearance of at least 12mm (1/2") is required at the back as shown. 11), the aluminium flue pipe is removed from the refrigerator and discarded. [. . . ] (As the pins of the existing trailer plug and socket will normally be taken up with lights and other electrical equipment, it will probably be necessary to install an additional trailer plug and socket and use two of its pins for the refrigerator supply). A suitable switch or plug and socket may also be installed inside the caravan so that the refrigerator can conveniently be disconnected from the 12V supply when required. When operating on 12 volts, the refrigerator has a relatively high current consumption and it is only intended to be used by this method of operation whilst the engine is running and charging the battery, and for short stops, otherwise the battery may become discharged to a point where it will not re-start the car engine. 12 volt operation is not thermostatically controlled and the 85 watt heating element is 'on' all the time the refrigerator is connected to the 12V supply. [. . . ]