User manual AEG-ELECTROLUX RM2210-1

[. . . ] Transit damage must be reported to whoever is responsible for delivery not later than seven days after the refrigerator was delivered. DATA PLATE Check the data plate, inside the refrigerator, to ensure that you have received the right model. the following details: Model designation Product number Serial number Voltage Gas pressure RM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Since these details will be needed if you have to contact service personnel, it is a good idea to make a note of them here. TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6. When the flame lights, the sparking stops automatically and the lamp stops flashing. [. . . ] Check the formation of frost regularly every week and when it gets about 3 mm thick, defrost the refrigerator. To defrost the refrigerator, turn it off and remove the ice trays and the food item, leave the cabinet and freezer doors open. Do not try to accelerate defrosting by using any kind of heating appliance, as this might damage the plastic surfaces of the refrigerator. Defrost water runs from a drip tray to a receptacle at the rear of the refrigerator where it normally evaporates. Heavy frosts build up on the freezer plate and the cooling fins, and a lot of defrost water: Move the plastic drain tube in to a watertight bucket or container. (Access through the lower ventilation grill on the outside of the vehicle). Defrost water in the freezer compartment should be mopped up with a cloth. Place the food items back inside but wait until the refrigerator is cold before making ice cubes. WINTER OPERATION Please check that the ventilation grilles are not blocked by snow, leaves etc. ELECTROLUX ventilation grilles model L500, can be fitted with winter covers, model WA130, to protect the cooling unit against cold air. The covers may be fitted when the outside temperature is below approx. 10°C and should be fitted when the temperature is below the freezing point. 4 mm Before starting the mounting work, check that the panel dimensions are in compliance with those given in the table and the instructions are read thoroughly. When mounting the panel, proceed as follows: Upper door MAINTENANCE Always turn to a qualified service technician who is familiar with LP gas systems and refrigerator. We recommend that a service technician check the refrigerator once a year. · · · · · · · · · · · · · · · · remove the two screws holding the control panel, pull out the two knobs (energy selector and thermostat) unscrew the upper hinge pin and remove the door unscrew the upper part of the door frame, remove the old panel insert the new panel and push the panel downwards fasten the upper part of the door frame with its three screws please note that the panel must be changed on the lower door, before the upper door can be mounted Check all connections in the LP gas system for gas leaks. Check that the burner is clean and free from combustible material. SOME USEFUL HINTS Make sure that: lower door unscrew the middle hinge pin and remove the door unscrew the lower part of the door frame, remove the panel stop (2x) and remove the old panel insert the new panel and push the panel upwards, put the panel stop back in place and fasten the lower part of the door frame with its three screws replace the lower door replace the upper door replace the control panel with its two screws and put on the knobs. · · · · · · The refrigerator is not operating on 12 V when the vehicle is parked; otherwise you will drain the car battery in a short time. Defrosting is carried out periodically The refrigerator is clean and dry with the door left open when it is not to be used for some time. Note: This is the only approved means of securing the refrigerator to the enclosure and to the vehicle. Fasteners penetrating other parts of the insulation (PU) foam of the refrigerator might damage components like electric wiring etc. FIG. 2 Side ventilation. The refrigerator unit is ventilated via two openings in the wall of the caravan (fig. Fresh air enters through the lower opening and warm air is discharged through the upper one. The lower opening should be located at floor level (to allow any leaking gas to escape to the outside). The upper ventilation opening should be located above the condenser, as high as possible, to ensure good ventilation. Roof ventilation The ventilation of the cooling unit can also be done via one opening in the wall of the caravan and one on the roof for the roof vent (fig. [. . . ] 3c View from above Door RM 6501 1400 1400 1250 LP GAS CONNECTION The refrigerator is designed for operation on LP gas, the pressure of which must be 28 mbar for Butane and 37 mbar for Propane. The refrigerator is not designed for operation on town gas or natural gas. CHECK THAT THE GAS SUPPLIED TO THE REFRIGERATOR IS AT THE CORRECT PRESSURE. The gas installation should only be carried out by a person experienced in gas fitting. [. . . ]