User manual AEG-ELECTROLUX T57840

[. . . ] LAVATHERM 57840 User manual Condenser Dryer 2 Dear Customer Thank you for choosing one of our high-quality products. With this appliance you will experience the perfect combination of functional design and cutting edge technology. Convince yourself that our appliances are engineered to deliver the best performance and control - indeed we are setting the highest standards of excellence. In addition to this you find environmental and energy saving aspects as an integral part of our products. [. . . ] (The laundry should be taken out towards the end of the anti-crease phase at the latest to prevent creases from forming. ) If LONG ANTIfunction has been selected, the anti-crease phase CREASE ANTIKREUK LANG is lengthened by 60 minutes. After each drying cycle: - Clean the micro-fine filter and fine filter - Drain the condensed water container (See chapter "Care and cleaning". ) 5. Close the door. 20 Care and cleaning Care and cleaning Cleaning fluff filter The filters collect all the fluff which accumulates during drying. To ensure that the dryer works perfectly, the fluff filters (micro-fine filter and fine strainer) must be cleaned after every drying cycle. Never operate the dryer without fluff filters or with damaged or blocked fluff filters. Open loading door Use a damp hand to clean the micro- fine filter, which is built into the lower part of the loading aperture. 3. After a period of time, a patina due to detergent residue on laundry forms on the filters. It can be positioned with the tooth facing to the left or to the right). It is best to use a damp hand for this purpose. Clean the entire filter area The strainer area does not have to be cleaned after every drying cycle, but should be checked regularly and cleaned of fluff if necessary. To do this, grip the top of the large mesh filter and pull it forwards until it comes loose from the two brackets. Press both journals of the large mesh filter into the brackets on the loading door until they snap into place. Press against the large mesh filter until it locks into the interlock. 22 Care and cleaning If the fine strainer is not fitted, the large mesh filter will not snap into place and the loading door cannot be closed. Cleaning the door seal Wipe the door seal with a damp cloth immediately after the drying cycle has finished. Emptying the condensate tank Empty condensate tank after every drying cycle. If the condensate tank is full, an active programme will break off automatically icon on the display will light up. In order to continue and the EMPTY CONTAINER the programme, the condensate tank must first be emptied. The condensate is not suitable for drinking or for preparing foodstuffs. Take out drawer containing condensed water container completely 1 and pull up the condensed water container's drainage pipe as far as it will go 2. 2 1 Care and cleaning 2. If the programme has been interrupted as a result of the condensate tank being full: Press the START PAUSE START PAUZE button to continue the drying cycle. 23 The condensate tank has a volume of approx. This is sufficient for around 7kg of laundry which has previously been spun at 1000 revolutions/ minute. with a coffee filter) to remove any residue and small pieces of fluff. Cleaning heat exchanger If the HEAT EXCHANGER is displayed, the heat exchanger needs to be cleaned. Operating when the heat exchanger is blocked with fluff can damage the dryer. To do this, press the release button on the bottom of the door aperture and open the door in the plinth to the left. Clean fluff from the inside of the door and the heat exchanger front chamber. Use the handle to pull the heat exchanger out of the base and carry it horizontally to prevent any remaining water from spilling. [. . . ] Re-insert cover plates B and C on the opposite site having first rotated them through 180°. 4. 5. 6. 34 Installation Unscrew cover plates E from the E front of the machine, rotate through 180°, screw on the oppoG site side. Unscrew door lock F, push down slightly and remove from the front of the machine. Press snap-in button G in and G down, press cover down slightly and remove from front of the machine. Change door lock F over to the opposite side, insert the cable connector and screw down the door interlock. [. . . ]