User manual AEG STEP 570 X

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual AEG STEP 570 X. We hope that this AEG STEP 570 X user guide will be useful to you.


AEG STEP 570 X : Download the complete user guide (2393 Ko)

Manual abstract: user guide AEG STEP 570 X

Detailed instructions for use are in the User's Guide.

[. . . ] Measured sound value Measured vibration value Use Typically the A-weighted sound pressure level of the tool is 82 dB (A). This jig saw can cut wood, plastic and metal; it can cut straight lines, bevels, curves, and internal cut-outs. Connect only to a single-phase AC current supply and only to the mains voltage specified on the rating plate. When fitting the plug, make sure that the brown (live) wire of this appliance is connected to the plug terminal marked L or coloured red, and the blue (neutral) wire of this appliance is connected to the plug terminal marked N or coloured black. [. . . ] Release the tension lever and the saw ); the slot in the plunger must always be at an angle to the saw blade (see illustration below). Fit the saw blade into the groove in the In the interest of continuous improvement of our products, technical specifications are subject to alteration without prior notice. Setting an angle Loosen the fixing screw, pull the base plate out of the mounting, set it at the required angle (15o, 30o, 45o), push it back into the mounting and tighten the fixing screw again. Angles other than 45o can be set by not pushing the base plate back into the mounting. Loosen the fixing screw, push the base plate to the rear and tighten the fixing screw again. For cutting a hole with a Moving back short saw blade and sawing near the edge. Take the fixing screw out, push the base plate to the rear and screw the fixing screw tightly into the rear hole. In this position the base plate can also be off-set in longitudinal direction. Push the transparent cover downwards to ensure The anti-splintering device almost entirely prevents the edge of the wood from splintering. Place the anti-splintering device as shown in the illustration with the smooth side downwards and flush with the base plate (this is only possible with the base plate in the forward position). The letters A to G are printed on the speed control, meaning: A = lowest stroke rate G = highest stroke rate ENGLISH 3 STEP 570 X, STEP 600 X The stroke-rate (= movements per minute of the saw blade) can be infinitely varied by means of the adjustment wheel. The stroke rate appropriate to the material being worked on can be taken from the following table, and the corresponding letter shown on the setting wheel. By adjusting the pendulum action the cutting depth of the saw blade teeth is increased or decreased. As a rule of thumb: Soft material Hard material Clean cut surface Large pendulum stroke Small or no pendulum stroke No pendulum stroke The appropriate degree of pendulum effect can be taken from the following chart and compared with the marking at the pendulum stroke lever. The stroke rate shown in the chart is only a suggestion for your general guidance!The stroke rate can be set on the stroke rate control even while the motor is running. Position the machine with the front part of the base plate on the material, and Press the machine downwards onto the material and guide it along the cutting line. Light pressure on the saw blade is sufficient to achieve the optimum rate of sawing. [. . . ] For cutting from the left or from the right, push the parallel guide in from the appropriate side. Push the parallel guide, with the contact surface facing upwards, through the lugs in the base plate and fasten it in position with the capstand­headed screw. Ensure that the saw blade and the circle centre point form one single line. In order to guarantee constant readiness for operation, the machine should be checked for worn carbon brushes at one of the AEG after­sales service agencies. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE AEG STEP 570 X




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual AEG STEP 570 X will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.