Detailed instructions for use are in the User's Guide.
[. . . ] This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference will not occur in a particular installation. If this equipment does cause by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio / TV technician for help. [. . . ] - Do not mix using different kind of new and used batteries together to avoid leakage.
14
5. Connect Accessory Devices
Connecting a DVD player or other equipment Switch off TV and external equipment before connecting cables. Connect a DVD player or other equipment's Component Video Out (Y, Cb, Cr / Y, Pb, Pr) to the TV's corresponding Component In (Y, Cb, Cr / Y, Pb, Pr) jacks on COMP1 or COMP2. Press SOURCE to select COMPONENT 1 or COMPONENT 2 signal source.
Green
Red Blue White
Red
DVD or Set-top box
Connecting the Computer Switch off TV and external equipment before connecting cables. Press SOURCE to select VGA signal source.
15
CONNECT ACCESSORY DEVICES
POWER ON, OFF
OTHER FUNCTION
Connecting the DVD or VCR player devices Switch off TV and external equipment before connecting cables. Connect a DVD or VCR player's Video Out to the TV's Video In jack by a Video cable. Connect a DVD or VCR player's S-VIDEO Out to the TV's S-VIDEO In jack by a S-VIDEO cable. Connect a DVD or VCR player's Audio Out to the TV's L/R jacks by a Audio cable, in this stage, the S-VIDEO and VIDEO is sharing this L/R Audio in channels. Connecting AUDIO OUT jacks to a stereo amplifier Switch off TV and external equipment before connecting cables. Connecting directly to cable or an antenna When using 75 coaxial Aerial: Connect directly to the RF terminal of the tuner. VHF Antenna
Yellow
Red White Fig1.
DVD or VCR player
White
Red
Fig2. After you choose the POP mode, all settings are only aimed at the active window.
(Continued on next page)
19
USING THE POP DOUBLE-WINDOW FEATURE
OSD OPTION ADJUSTMENT
OSD FUNCTIONS
To display a picture from an external source in the POP window: 1. Repeatedly press SOURCE to select the input source for the POP window.
To change the PIP picture size:
Press PIP SIZE button to select the PIP picture size, such as: Small, Middle, Large.
To change the PIP position:
Press PIP POS button to change the PIP window position under PIP mode, it display as following; Right Down Left Down Left Up Right Up Right Down
PIP SIZE PIP POS
Left Up
Right Up
ENTER
Left Down
Right Down
Switching the pictures:
When in Basic PIP mode, press "ENTER" to swap main or sub pictures; When in LR POP mode, press "ENTER" swap the L/R pictures. When the red frame is displaying in main window, the sound goes out of main window source. If it display in sub window, the sound goes out of sub window source.
To change Main or Sub sound:
6. 5 OSD Option Adjustment
Learning about the menu system After you have installed the batteries and programmed the remote control, you will need to set some preferences on the TV using the menu system. You can access the menu using the buttons on your TV or remote control. The OSD menu displayed in the following sequence (circular display):
Video Audio Misc TV Geometric (Continued on next page)
20
Press MENU to display the menu system. Press ENTER on the remote control or SOURCE on the TV control panel to activate the function settings in the menu. If you do not make a selection within 15 seconds, the main menu closes automatically; the other menus close automatically within 6 seconds. To close an on-screen menu instantly, press MENU on the remote control or MENU on the control panel.
SOURCE
ENTER
MENU
TV control panel
CH.
SOURCE MENU
VOL.
STANDBY
SOURCE MENU
6. 6 OSD Functions
1 Using the Video Menu
Option Contrast Brightness Back Light Saturation Hue Sharpness Phase Color Temperature Advanced Picture Adjust Note: Press / 0~100 0~100 Bright, Middle, Dark 0~100 -30~+30 0~7 0~31 Cool, Middle, Warm, User Description Reduce/Enhance Darken/Brighten Adjust the balance of back light Decrease/Increase of color Decrease/Increase Soften/Sharpen Decrease/Increase Adjust the balance of whitening Adjust the picture effect
Video Menu is just for TV, AV, S-Video, Component 1 and Component 2 input source mode. Contrast, Brightness, Saturation, Hue, Sharpness can be adjusted only if picture mode is in USER mode. When smart picture mode is pre-set, the value of the above settings will be different according to different input source. [. . . ] 1 2 3 4 5 6
Resolution 480i 480p(720x480) 576p(720x576) 720p(1280x720) 720p(1280x720) 1080i(1920x1080)
- When the signal received by the Display exceeds the allowed range, a warning message "Out Of Range" shall appear on the screen. - You can confirm the input signal format from the on-screen.
45
CLEANING AND SIMPLE TROUBLESHOOTING
9. Cleaning and Simple Troubleshooting
1 Important: - Make sure that the power cable is removed from the AC outlet before cleaning the product. - Do not use volatile solvent (such as toluene, rosin and alcohol) to clean the Display. [. . . ]