User manual ALCATEL-LUCENT 530

[. . . ] SpeedTouchTM510/530 Multi-User ADSL Gateways Setup and User's Guide Release R4. 2. 7 500 SERIES SpeedTouchTM 510/530 Setup and User's Guide Release R4. 2. 7 Status Reference Short Title Copyright v3. 0 E-SIT-CTC-20030306-0003 Setup and User's Guide ST510(i)/530(i) R4. 2. 7 © 2004 THOMSON Telecom. Passing on, and copying of this document, use and communication of its contents is not permitted without written authorization from THOMSON Telecom. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by THOMSON Telecom. THOMSON Telecom assumes no responsibility or liability for any errors or inaccuracies that may appear in this document. Contents 1 1. 1 1. 2 1. 2. 1 1. 2. 2 1. 2. 3 1. 3 1. 3. 1 1. 3. 2 1. 4 SpeedTouchTM Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] it becomes idle. E-SIT-CTC-20030306-0003 v3. 0 37 2 SpeedTouchTM Internet Connectivity 2. 3 Connect to the Internet via a Host PPPoE Dialin Client Introduction This section explains how you can connect to the Internet using a dial-in application on a computer running: · · Microsoft Windows XP. Mac OS X. 38 E-SIT-CTC-20030306-0003 v3. 0 2 SpeedTouchTM Internet Connectivity 2. 3. 1 Using the Windows XP Dial-in Client Configuring a dial-in connection on a Windows XP platform To create a new dial-in connection proceed as follows: 1 2 3 4 On the Start menu, click Control Panel. 5 The following window appears: Select the Connect to the Internet option and click Next to continue. 6 The New Connection wizard asks you how you connect to the internet: Select Set up my connection manually and click Next to continue. E-SIT-CTC-20030306-0003 v3. 0 39 2 SpeedTouchTM Internet Connectivity 7 The New Connection wizard asks you how you connect to the internet: Select Connect using a broadband connection that requires a user name and password. Follow the instructions and enter the required information where needed. At the end of the configuration the following window appears: 9 Click Finish to complete the configuration. Starting a dial-in Internet session from Windows XP To connect to the internet proceed as follows: 1 2 On the Start menu, point Connect To and click Internet. The Connect Internet window appears: Enter User name and password if needed and click Connect. 3 Your computer connects to the internet. 40 E-SIT-CTC-20030306-0003 v3. 0 2 SpeedTouchTM Internet Connectivity 2. 3. 2 Using the Mac OS X Dial-in Client Configuring a dial-in connection on a Mac OS X platform To create a dial-in connection proceed as follows: 1 2 3 On the Apple menu, click System Preferences. The Network window appears: In the Show list, select Ethernet Adaptor (enx) and click the PPPoE tab. 4 Enter the Account Name and Password provided by your Service Provider and Click Apply now. Starting a dial-in connection on a Mac OS X platform To connect to the internet proceed as follows: 1 2 Click the Internet Connect icon in the dock. The following window appears: Make sure Ethernet Adaptor (enx) is selected in the Configuration list. 3 Your computer connects to the internet. E-SIT-CTC-20030306-0003 v3. 0 41 2 SpeedTouchTM Internet Connectivity 42 E-SIT-CTC-20030306-0003 v3. 0 3 SpeedTouchTM Web Interface 3 SpeedTouchTM Web Interface Introduction The SpeedTouchTM comes with integrated local configuration capabilities. The local configuration, via the SpeedTouchTM web interface, is based on the HTTP server/web browser concept. It allows you to configure your SpeedTouchTM via a web browser using HTML pages from any local computer attached to the Ethernet interface(s) and/or from the PC connected via the USB interface (in case of a SpeedTouchTM with USB connectivity). Requirements Before you access the SpeedTouchTM pages, make sure that your browser is configured to directly connect to the SpeedTouchTM, i. e. If required, you can disable the proxy server for the time you want to access the SpeedTouchTM web pages. For more information on how to disable your web browser's proxying, please consult the web browser's user's guide. Use of the SpeedTouchTM web interface In most cases, the SpeedTouchTM is correctly configured for your Internet connectivity via the appropriate configuration profile/file and no further configuration on the web interface is needed. Access to the web pages is only required for some advanced configurations and upgrading/updating or backing up the SpeedTouchTM configuration. Access to the SpeedTouchTM web interface To access the SpeedTouchTM web pages: 1 2 3 Start the web browser on your computer. Browse to the SpeedTouchTM at the SpeedTouchTM's IP address (in most cases 10. 0. 0. 138). [. . . ] (none of the LEDs light up) Solution Make sure that the SpeedTouchTM is plugged into an electrical outlet. Make sure that you are using the correct power supply for your SpeedTouchTM device. Link integrity/Activity LED of particular Ethernet port does not light up. Make sure that the cable(s) are securely connected to the 10/100Base-T port(s). [. . . ]