User manual ALCATEL-LUCENT SPEEDTOUCH 180
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual ALCATEL-LUCENT SPEEDTOUCH 180. We hope that this ALCATEL-LUCENT SPEEDTOUCH 180 user guide will be useful to you.
You may also download the following manuals related to this product:
ALCATEL-LUCENT SPEEDTOUCH 180 (1192 ko)
Manual abstract: user guide ALCATEL-LUCENT SPEEDTOUCH 180
Detailed instructions for use are in the User's Guide.
[. . . ] SpeedTouchTM180
IEEE802. 11g Wireless Access Point
Setup and User's Guide
Release R1. 0
SpeedTouchTM 180
Setup and User's Guide Release R1. 0
Status Reference Short Title Copyright
v2. 0 E-DOC-CTC-20040401-0003 Setup and User's Guide ST180 R1. 0
© 2004 THOMSON. Passing on, and copying of this document, use and communication of its contents is not permitted without written authorization from THOMSON. The content of this document is furnished for informational use only, may be subject to change without notice, and should not be construed as a commitment by THOMSON. THOMSON assumes no responsibility or liability for any errors or inaccuracies that may appear in this document.
Contents
1
1. 1 1. 2 1. 3 1. 3. 1 1. 3. 2 1. 3. 3
SpeedTouchTM180 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Enter your new password in the New password box and re-enter it in the New password box. In the Idle time out box, you can specify a the maximum period of time (in minutes) for which the login session is maintained during inactivity. If your password is lost, or you cannot gain access to the management interface, perform a power reset. For more information, see "3. 2 SpeedTouchTM180 Default Configuration" on page 36.
Note Note
E-DOC-CTC-20040401-0003 v2. 0
17
2 SpeedTouchTM180 Web Interface
Operating Mode
Click this link to display the Operating Mode page:
Under Operating Mode, you can select: · · · Access Point: Provides simple, wireless access to your network or internet gateway. Client Bridge (Infrastructure): Enables you to establish a wireless connection to an Access Point. Client Bridge (AdHoc): Enables you to directly communicate with other wireless clients without the need of Access Point. Note The performance of your wireless network, however, will decrease considerably as the number of AdHoc devices on your network increases.
·
Repeater Extends the range of an existing Access Point. For more information, see "1. 3 SpeedTouchTM180 Configuration" on page 9.
Note Language Settings
Click this link to display the Language Settings page:
To change the web page language: 1 2 3 Select the language of your choice in the Please select your language list. The SpeedTouchTM180 changes the web page language, without restarting.
18
E-DOC-CTC-20040401-0003 v2. 0
2 SpeedTouchTM180 Web Interface
2. 2 LAN Links
Introduction You can configure the LAN settings from here. The appearance of this page will differ depending on your SpeedTouchTM operation mode: Use the LAN Settings page to configure the LAN IP address. In Access Point Mode, you may choose to use a static address or to obtain an IP address from a DHCP server.
Lan Settings page
Note
The device will automatically start up with its default static IP address, 10. 0. 0. 140.
The LAN links page allows you to configure: · AP Name: DNS name of the access point. (This naming feature is optional. ) Note · Do not use spaces in the AP name. Note This field will not be shown in Client Bridge mode.
If you choose to configure the SpeedTouchTM180 statically two additional fields become available: · · IP address: The IP Address of the SpeedTouchTM180. Subnet Mask: The subnet mask of the network.
E-DOC-CTC-20040401-0003 v2. 0
19
2 SpeedTouchTM180 Web Interface
2. 3 Wireless Links
Introduction This section describes following menu items: Topic Basic Setting WEP Configuration WPA Configuration Client List Connection Control Repeater Settings Page 21 23 25 27 28 29
20
E-DOC-CTC-20040401-0003 v2. 0
2 SpeedTouchTM180 Web Interface
2. 3. 1 Basic Setting
Availability Access Point and Repeater Mode The Basic Setting page is available in all operation modes. Click Basic Setting to set the channel, Service Set ID (SSID), and transmit speed for your wireless network.
The wireless settings are listed in the table below. Parameter Enable Wireless Networking Channel Description Enables/disables wireless networking. The radio channel used for the SpeedTouchTM to communicate with the wireless clients. The SpeedTouchTM will automatically assign itself a radio channel, or you may select one manually. This should be set to the same value as other wireless devices on your network. The SSID is case sensitive and can consist of up to 32 alphanumeric characters. By default the SpeedTouchTM180 broadcasts its Network Name (SSID) to the WLAN clients. WLAN clients using this broadcast SSID or using an empty SSID can join the SpeedTouchTM180. [. . . ] Some of the problems you may encounter are: · · · One of the panel indicators is off Troubleshooting Chart Problem SpeedTouchTM180 does not work (none of the LEDs light up) Action Make sure that the SpeedTouchTM is plugged into a power socket outlet. Make sure that you are using the correct power supply for your SpeedTouchTM device. Make sure that the LAN cable are securely connected to the 10/100Base-T port. Make sure that you are using the correct cable type for your Ethernet equipment. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ALCATEL-LUCENT SPEEDTOUCH 180
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ALCATEL-LUCENT SPEEDTOUCH 180 will begin.