User manual ALPINE PXI-H990

[. . . ] Failure to do so may result in electric shock or injury due to electrical shorts. Arrange wiring and cables in compliance with the manual to prevent obstructions when driving. Cables or wiring that obstruct or hang up on places such as the steering wheel, gear lever, brake pedals, etc. Doing so will exceed the current carrying capacity of the wire and result in fire or electric shock. 2-EN DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES. [. . . ] · Alpine accepts no responsibility for damaged or lost data in your computer etc. , even if data etc. , is damaged or lost while using this product. Wiring Connections Improper wiring connections could cause serious damage to your audio system. Fuse When replacing the fuse(s), the replacement fuse must be of the same amperage as shown on the fuse holder. If the fuse(s) blows more than once, carefully check all electrical connections for shorted circuitry. Do not attempt to repair the unit yourself; return it to your Alpine dealer or nearest Alpine Service Station for servicing. Temperature In order to ensure proper performance, be sure the temperature in your vehicle is above 14°F (­10°C) and below 140°F (60°C) before turning your unit on. Good air circulation is essential to prevent internal heat build-up in the unit. 4-EN Contents PRECAUTIONS Accessories Installation Connections Examples of system expansion 2 6 7 10 12 IMPORTANT Please record the serial number of your unit in the space provided below and keep it as a permanent record. The serial number plate is located on the bottom of the unit. SERIAL NUMBER: INSTALLATION DATE: INSTALLATION TECHNICIAN: PLACE OF PURCHASE: To prevent external noise from entering the audio system. · Locate the unit and route the leads at least 10 cm away from the car harness. · Keep the battery power leads as far away from other leads as possible. · Connect the ground lead securely to a bare metal spot (remove any paint, dirt or grease if necessary) of the car chassis. · If you add an optional noise suppressor, connect it as far away from the unit as possible. · Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information. 5-EN Accessories IONBUS cable (6m) DVD Audio Link cable (6m) Tapping screws (M4 x 14) x4 Microphone (6m) Microphone terminal connec1 tion cable (6m)* Hexagonal wrench (M3) Bracket* 2 Bracket pan head screws 2 (M4 x 8)* Cord clamp x8 Ferrite Core x4 x2 *1 Used only when setting the microphone built in the monitor (TMI-M990, sold separately) as the Road EQ microphone. · Ferrite Core Attach the Ferrite Core (included) to the both ends of the IONBUS cable at a location where the product does not touch the core when installing. (When connecting to the main unit, attach the core at a location of approx. 4 cm from the terminal end. ) 4cm NOTE · For connection of PXI-H990, the battery power cable (sold separately), ground cable (sold separately), remote out cable (sold separately), are necessary. 6-EN Installation · Mounting the base unit 1. WARNING: When making holes, be careful not to damage pipes, tanks, electric wires, etc. Securely mount the unit using the four included tapping screws (M4 x 14). Tapping screws (M4 x 14) 7-EN < Setting up two PXI-H990s > Find a location that can accommodate both unit together then proceed with the following procedure. To set up two PXI-H990s, first connect both base units before setting them up. Remove the screw from the top part of one base unit marked with # using the supplied hexagonal wrench (M3). Before re-attaching the plate, change the INDICATOR switch to "REVERSE". (For Basic Connections Diagram, refer to page 10) # # 8-EN 3. Place two base units side by side, and attach the brackets with the supplied bracket pan head screws (M4 x 8). Bracket pan head screw (M4 x 8) 4. [. . . ] When an Ai-NET compatible changer is not connected, then the KCI-500B does not need to be connected. For details about connections, refer to the instruction manual of the product you are connecting with. 13-EN R ALPINE ELECTRONICS MARKETING, INC. 1-1-8 Nishi Gotanda, Shinagawa-ku, Tokyo 141-0031, Japan Phone 03-5496-8231 ALPINE ELECTRONICS OF AMERICA, INC. Phone 1-800-ALPINE-1 (1-800-257-4631) ALPINE ELECTRONICS OF CANADA, INC. [. . . ]