User manual ALPINE SWD-2030

[. . . ] Arrange the wiring and cables in compliance with the manual to prevent obstructions when driving. Cables or wiring that obstruct or hang up on places such as the steering wheel, gear lever, brake pedals, etc. When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. 2 DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS. [. . . ] To ensure safety, always contact the dealer where you purchased this product to have the work done. KEEP THE VOLUME AT A LEVEL WHERE YOU CAN STILL HEAR OUTSIDE NOISE WHILE DRIVING. Use for other than its designed application may result in fire, electric shock or injury. 3 CAUTION IN USE DO NOT USE A MOBILE PHONE NEAR THIS PRODUCT. If there is distortion or a popping noise from the subwoofer, the input level is too high. If the subwoofer has prolonged use in this condition, this may result in deterioration of performance or may cause damage to the subwoofer. DAMAGE CAUSED BY EXCESSIVE INPUT LEVEL WILL NOT BE COVERED UNDER WARRANTY. EN TROUBLESHOOTING If you have a problem with the product then please check the following before taking for repair. SYMPTOMS Unit does not operate. (For example if the fuse is blown) REASON SOLUTION The head unit is not powered up. Power up the head unit. Earth lead is not connected properly. Check the earth lead connection The power lead to the battery is not connected properly. Check the battery lead connection There is power but no sound. The fuse is blown. Replace with a fuse of the correct rating. Remote turn on lead is not connected properly. Check the remote turn on lead connection RCA leads are not connected. Connect RCA leads correctly. Speaker level input cables are not connected properly Check the speaker level input cable connections. The gain is not at the correct level for the system. Adjust the gain setting to an appropriate level for the system. 4 SPECIFICATIONS MAX POWER OUTPUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CROSSOVER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INPUT IMPEDANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OPERATIONAL VOLTAGE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EARTH TYPE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SENSITVITY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DIMENSIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . WEIGHT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350W 50~150Hz 20k Ohm (Line Input) 50k Ohm (Speaker Input) DC 14. 4V (Operational between: 11~16V) Negative Earth 96dB/10W. m 340mm x 390mm x 395mm 9. 5kg EN PACKING LIST PRODUCT NAME 7-Pin connector QTY 1 PRODUCT NAME Speaker to RCA connector (1M) QTY 2 INTRODUCTION · Please ensure that there is sufficient length of the various cables for your desired subwoofer location. Please read the instructions of the product that will be used with the SWD-2030, alongside this manual during installation. 1. INSTALLATION 1 2 Park the car at a safe place, on a level surface. Work out where to install the subwoofer, and check that there is sufficient cable length. Carry out the Installation. When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precautions may result in fire. 5 WARNING - DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS. Bolts or nuts used for the brake or steering systems (or any other safety related system), or tanks should NEVER be used for installations or ground connections. Using such parts could disable control of the vehicle and cause fire, etc. 1 2 Check for instalation locations and possibilities. [. . . ] CAUTION - ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE. Route the cables and wiring away from moving parts (like the seat rails) or sharp or pointed edges. If wiring passes through a hole in metal, use a rubber grommet to prevent the wires insulation from being cut by the metal edge of the hole. EN 2 3 4 Reconnect the negative lead to the battery terminal By switching on the head unit, verify that the subwoofer is working. Check that all electrical functions of the car are operational. 7. Input mode selector (line or high-level) Indicator for auto-remote by radio outputs Volume level adjustment Remote signal indicator Adjustment lowpass filter Indicator Low Battery Phase shift adjust CAUTION DO NOT EXCEED THE INPUT LEVEL SPECIFIED FOR THIS PRODUCT. [. . . ]