User manual ALPINE TMI-M990

[. . . ] 1-1-8 Nishi Gotanda, Shinagawa-ku, Tokyo 141-0031, Japan Phone 03-5496-8231 ALPINE ELECTRONICS OF AMERICA, INC. Phone 1-800-ALPINE-1 (1-800-257-4631) ALPINE ELECTRONICS OF CANADA, INC. 7300 Warden Ave. , Suite 203, Markham, Ontario L3R 9Z6, Canada Phone 1-800-ALPINE-1 (1-800-257-4631) ALPINE ELECTRONICS OF AUSTRALIA PTY. 6-8 Fiveways Boulevarde Keysborough, Victoria 3173, Australia Phone 03-9769-0000 ALPINE ELECTRONICS GmbH Frankfurter Ring 117, 80807 München, Germany Phone 089-32 42 640 TMI-M990 OWNER'S MANUAL ALPINE ELECTRONICS OF U. K. [. . . ] In this case, perform operation with the buttons of the TMI-M990 main unit. 29-EN Other Useful Features V. SEL/ V. MUTE V. SEL/DISP. OFF Switching the Visual Source Only (Simultaneous Function) When an IONBUS compatible head unit is connected, you can watch the video portion of another source while listening to the current source. while listening to the FM, AM or a CD on the head unit. * (Picture) (Audio) AUX-3 DVD DVD DVD NAVI. DVD AUX-2 DVD AUX-1 DVD * When simultaneous is off. 30-EN 2 Press V. SEL/DISP. OFF. <Example> 1 Change to your preferred source (FM, AM, CD etc. ) on the head unit. For details, see the head unit operating instructions. Blackout Mode On and Off When Blackout mode is turned on, the display will turn off. The backlight life can be extended. The following operation is performed with the supplied remote control. 1 2 Press and hold V. SEL/V. MUTE for at least 2 seconds to start the blackout mode. To cancel Blackout mode, press and hold V. SEL/V. MUTE for at least 2 seconds. · If any button on the unit is pressed during Blackout mode, the function will be displayed for 5 seconds to show the operation before returning to Blackout mode. [When an IONBUS Compatible Head Unit is Connected] Operation can be performed with either the main unit switch or the remote control. The main unit switch operation is as follows. 1 Press and hold V. SEL/DISP. OFF for at least 2 seconds to start the blackout mode. To cancel Blackout mode, press and hold V. SEL/DISP. OFF for at least 2 seconds. · If any button on the unit is pressed during Blackout mode, the function will be displayed for 5 seconds to show the operation before returning to Blackout mode. Supplement See page 32 for supplementary information. 2 · The simultaneous function can only be used when an IONBUS compatible head unit is connected. mode sound of TMI-M990 during simultaneous operation, change the head unit source to AUX, NAVI. · When the simultaneous function is active and you change the head unit source, only the audio is switched and the simultaneous function is not cleared. To clear the simultaneous function, press V. SEL/DISP. OFF on the main unit to switch to video and audio from the same source. The simultaneous function can also be cleared by linking to when the DVI-9990R/DVI-9990E source switches. (General Setup Operation "Head Unit Linked Functions" page 43) 31-EN Other Useful Features Supplementary information This page includes supplementary information for pages 20 to 31. Please refer to these pages. TITLE Adjusting and Storing VISUAL EQ Description Adjusting and storing of VISUAL EQ can also be made from the setup. Operation from the main unit 1 Press and hold OPEN/CLOSE / SETUP for at least 2 seconds. 2 Press VISUAL EQ or OPEN/CLOSE / SETUP, and select an item to adjust from BRIGHT, COLOR, TINT, CONTRAST, SHARPNESS. 5 When the picture settings are complete, press VISUAL EQ or OPEN/CLOSE / SETUP and select V. EQ MEMORY. 8 After setting, press and hold OPEN/CLOSE / SETUP for at least 2 seconds. Operation from the remote control 1 Press and hold BAND/SETUP for at least 2 seconds. 2 Press or , and select an item to adjust from BRIGHT, COLOR, TINT, CONTRAST, SHARPNESS. 3 Adjust the image by pressing 4 When adjusting another item, repeat steps 2 and 3. [. . . ] When connecting with the IONBUS compatible head unit, do not connect the ignition lead. 9 Battery Lead (Yellow) Connect this lead to the positive (+) post of the vehicle's battery. p Ground Lead (Black) Connect this lead to a good chassis ground on the vehicle. Make sure the connection is made to bare metal and is securely fastened using the sheet metal screw provided. q Choke Coil with Fuse Holder (7. 5A) w Power Supply Connector e Remote Control Output Lead (White/Brown) Connect this lead to the remote control input lead. This lead outputs the controlling signals from the remote control. r Remote Control Input Lead (White/Brown) Connect the external Alpine product to the remote control output lead. t Display Output Terminal y RGB Input Terminal u S Video Input Terminal i AUX Input Terminals/AUX Output Terminals o System Switch Change to "1:SYSTEM" when the main unit is connected with an IONBUS compatible head unit. When not connected to an IONBUS compatible head unit, change to "2:STANDALONE". · Be sure to turn the power off to the unit before changing the switch position. 61-EN Installation and Connections System Example When Connecting External Equipment (If an IONBUS compatible head unit is not connected) System Switch: When "STANDALONE" is set (See page 58) NVE-N099P/NVE-N077PS Navigation system (Sold Separately) 6 1 TMI-M990 AV-Interface unit Amplified Speaker (Sold Separately) To Audio Input terminal 5 2 6 4 To Video Input terminal Rear monitor 2 (Sold Separately) To Audio Input terminal 9 7 3 8 9 TV TUNER (Sold Separately) REMOTE OUT (AUX1) p REMOTE IN (White/Brown) (White/Brown) REMOTE IN (AUX2) q REMOTE OUT (White/Brown) (White/Brown) 1 RGB Cable 2 Power Supply Connector 3 RGB Input Terminal Connect this to the RGB output terminal of the Navigation System. 4 AUX Audio Output (AUX1) (L) Terminal When the System Switch is set to STANDALONE: AUX1 Audio Output Terminal is used as the audio output for the main unit. [. . . ]