User manual AMICA KH 17129-3 E

[. . . ] We wish you a lot of satisfaction from choosing our kitchen extractor hood. Symbols appearing in these instructions have the following meaning: Important information concerning proper operation of the appliance and your personal safety. The manufacturer reserves the right to introduce changes which do not affect the operation of the appliance. LThe manufacturer will accept no responsibility Not conforming to these Not required, however it Ling, make sure that the L For details of the installation distance above an electric hob please refer to product technical sheet If the installation instructions of the gas cooker specify a greater distance, this must be taken into account (Fig. [. . . ] The other end of the duct should be directed to the room as it will discharge filtered air. Fan speeds The lowest and medium speeds should be used under normal conditions and with low concentration of fumes. The maximum speed should be used in case of high concentration of kitchen fumes, e. 4) - "-" and "+" touch sensors control cooker hood fan speed in the range from 1 to 4, - "+" touch sensor increases cooker hood fan speed - "-" touch sensor reduces cooker hood fan speed - Timer touch sensor activates fan timer (max 90 min. ) - Lights "L" touch sensor switches cooker hood lights on/off independently of fan operation. It can be programmed to automatically switch off the fan after 10 to 90 minutes in 10 minutes intervals. - In order to activate the timer function set the cooker hood fan at a required speed by pressing the "+" touch sensor and then touch the timer (clock) touch sensor. The display will show a flashing 0 to indicate that timer setup mode is activated. Now select the delay time to switch off the cooker hood fan by touching `'+`', keeping in mind that the number displayed musts be multiplied by the 10 minute interval (For example 1=10 min, 2=20 min, 3=30 min, and so on) - Once the required delay time is set, confirm it by touching the timer (clock) symbol again. A small flashing dot by the value corresponding to fan speed indicates that timer is counting down. To cancel the fan timer function, touch the timer (clock) sensor while the countdown timer is running. FILTER SATURATION INDICATOR* The cooker hood is equipped with an electronic filter saturation indicator: - Replace the charcoal filter ­ , , C" is displayed (220 hours of operation), - Clean the aluminium filter ­ , , F" is displayed (100 hours of operation), Neither of these indications affects cooker hood operation, however when C or F is shown, fan speed indication (0 to 4) is not displayed until the , , C" or , , F" symbol is cleared. Touch and hold timer sensor field for about 10 seconds to clear the , , C" or , , F" symbols. When the control panel shows dot (without any additional symbols), hood is in StandBy mode. To activate sensor control panel, please move your finger horizontal on the panel on all sensors from left. * according to the model Maintenance Regular maintenance and cleaning of the device will ensure faultless operation, and help extend the life of the unit. Attention should be paid to replacing grease and carbon filters according to instructions. Aluminium grease filter Cleaning For normal hood operation, aluminium grease filter should be cleaned every month in the dishwasher or by hand using a mild detergent or liquid soap. to replace: Dismantling of aluminium grease filter is shown on Figure 5. This filter should be replaced at least once every two months or more frequently if the appliance is used intensively. [. . . ] The local waste collection points, shops and communal units form an appropriate system enabling the disposal of the equipment. Handling the used electrical and electronic equipment and any hazardous substances contained therein in a correct manner is vital to avoid damage the local natural environment. Therefore care and responsibility should always be taken in the disposal of these products Warranty Warranty service as stated on the warranty card The manufacturer shall not be held liable for any damage caused by improper use of the product. The manufacturer hereby declares that this product meets the requirements of the following European directives: L Low Voltage Directive 2006/95/EC, l Electromagnetic Compatibility (EMC) Directive 2004/108/EC, l ErP Directive 2009/125/EC and has thus been marked with the symbol and been issued with a declaration of compliance made available to market regulators. [. . . ]