User manual AMX COLOR TOUCH PANELS WITH AUDIO (G3 FIRMWARE)

[. . . ] instruction manual CP4/A - 4" Color Touch Panels with Audio (Firmware version G3) Tou c h Pa n els an d A cc e ss o r ie s AMX Limited Warranty and Disclaimer AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX Corporation, with the following exceptions: · · · Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components that are warranted for a period of one (1) year. Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one (1) year. AMX Lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products, as long as the AMX Lighting products are under warranty. AMX Corporation does guarantee the control of dimmable loads that are properly connected to our lighting products. [. . . ] It does not matter whether the panel is in Wake/Sleep mode or whether the Light Sensor is set to Dim-Room mode (DRM) or Normal-Room mode (NRM). LS BUTTON ILLUMINATION mode sets the pushbutton LEDs to illuminate when the light sensor (LS) falls below its threshold value. In the case of a Dim-Room, refer to the light sensor section above for more information about the definition of a Dim vs. When the LS rises above its hysteresis (turn-on) value, in the case of a Normal-Room, the pushbutton LED illumination turns Off. An adjustment to this mode is also achieved through the use of the PBIL AXlink Send_Command. Refer to page 49 for more information. LED illumination is dependent only on the LS and corresponding light threshold. It does not matter whether the panel is in Wake/Sleep mode or whether the Light Sensor is set to DRM or NRM. BUTTON ILLUMINATION mode sets the pushbutton LEDs to either illuminate (On) or not (Off). An adjustment to this mode is also achieved through the use of the PBIL AXlink Send_Command. Refer to page 49 for more information. PIR/LS AUTO mode is a combination of the first two automatic mode buttons (PIR and LS button illumination). An adjustment to this mode is also achieved through the use of the PBIL AXlink Send_Command. The order of precedence for illumination of the pushbutton LEDs is PIR then LS. The pushbutton LEDs illuminate if there is PIR activity, without regard to the level 36 4" Color Touch Panels with Audio Designing Touch Panel Pages of the light sensor. The LEDs also illuminate if there is no PIR activity and the light sensor level falls below its threshold value. The order of precedence for turning Off the pushbutton LEDs is the LS then PIR. If the light sensor rises above its hysteresis (turn-on) value and there is no any activity coming from the PIR (thirty seconds of inactivity), the LEDs turn Off. Using the Audio and IR Device Setup page The speaker volume control, microphone control, and the IR device codes will be facilitated through a Audio And IR Device Setup Page. This page is used to configure the various features and parameters for the CP4/A panel sensors. Choose from any of these buttons and sliders to alter and set the properties for the speakers, IR receiver, and microphone (FIG. 31 Adjust Sensors page SPEAKER VOLUME allows the user to adjust the effective speaker volume. The panel consists of an up button (UP), a down button (DN), and a current setting indicator (range is between 0 and 32). An adjustment to the speaker volume is also achieved through the use of the SVOL AXlink Send_Command. Refer to page 50 for more information. MICROPHONE ADJUSTMENT allows the user to adjust the effective microphone volume. The panel consists of an up button (UP), a down button (DN), and a current setting indicator (range is between 0 and 32). [. . . ] Carefully flip the housing back onto the exposed AXT unit and align the connector opening with the on-board rear Phoenix connectors. Carefully grab the entire unit (housing and LCD) from both sides and rotate it over. 42 on page 75) into the interior of the unit by using a screwdriver to turn the screws clockwise. Carefully rotate the entire unit over and place the LCD and faceplate back onto a soft cloth to prevent scratching during the faceplate installation process. [. . . ]