User manual AMX RDD-DM4 4-CHANNEL INTEGRATED DIMMER MODULE

[. . . ] Installation Sheet RDD-DM4 4-Channel Integrated Dimmer Module 120, 240, 277 VAC The RDD-DM4 Four-Channel Integrated Dimmer Module controls up to six dimmed channels with four 1200 W onboard dimmers and two satellite connectors (for RDM series dimmer or switching modules). It is designed for use with the RDA series of enclosures, in an AMX LightingTM modular digital dimming system. [. . . ] 1 RDD-DM4 4-channel Integrated Dimmer Module RDD-DM4 UL and C-UL Ratings: (per circuit) Input · 120, 240, 277 VAC, single phase, 3-wire, 50/60 Hz, 2400 W, one feed · 120 , 240, 277 VAC, single phase, 4-wire, 50/60 Hz, 4800 W, dual feed Output · · · · 1200 W max. total, all four channels on with dual 2400 W feeds Feed circuit #1 goes to dimmer 1 and 3; feed circuit #2 goes to dimmer 2 and 4. FIG. 2 RDD-DM4 connections Connecting AXlink: Connect the 4-pin captive-wire AXlink from the RDD-DM4 to the Central Controller for AXlink control of the dimming system. PWR RDD-DM4 AXP AXM GND (optional) PWR AXP AXM GND Specifications · · · · · · · · Dimensions (HW): 5. 87" x 10. 0" (149. 00 mm x 254. 00 mm) Use wires rated at 75°C (167°F) Torque terminals to 20 in-lbs (2. 3 N/M) Max. wire size: 10 AWG (4 mm²) Wire stripping length: 0. 35" (9 mm) Weight: 4. 5 lbs (2. 04 kg) BTU/hr: 300 single feed (2400 W); 600 dual feed (4800 W) Power consumption: 50 mA @ 120 VAC, 25 mA @ 240 VAC, 22 mA @ 277 VAC · Control port current: 200 mA @ 12 VDC Central Controller FIG. 3 Connecting AXlink Connecting PROlink: Connect the orange 4-pin captive-wire PROlink connector from the RDD-DM4 to a PRO-DP8 PROlink wall panel. PRO-DP8 +12 PR+ PRGND Pack 1 Pack 2 +12 PR+ PRGND FIG. 4 Connecting PROlink Line-in Connections: Dual 20 A Inputs Using two feeds for line 1 and line 2 provides two, 20 A inputs. Dry Closure Default Presets Contact Closure 1 2 Bridging line 1 and line 2 provides a single 20 A input. 3 4 5 Default Function Channel 1 at 100% in 1 second Channel 2 at 100% in 1 second Channel 3 at 100% in 1 second Channel 4 at 100% in 1 second Channel 5 at 100% in 1 second Channel 6 at 100% in 1 second Pack on (channels 1-6) Pack off (channels 1-6 All other channels are undefined. 20 A Bridged 20 A Input FIG. 5 Line-in Connections 6 7 8 Connecting Dry Closures: Use the 8 (+ common) dry closures with a WPD8 eight-button wall panel. 1 2 3 4 5 6 7 8 COM Each contact (1 - 8) is preprogrammed with a default preset. Refer to the AMX Lighting Control System instruction manual for details on dry closure default presets and recording new presets. Setting AXlink and PROlink Address Numbers: AXlink Address PROlink Address Test FIG. 6 Dry closures connection Each contact closure connection (1 - 8) is pre-programmed with a default preset. The table below shows the default presets for each contact closure. Set the AXlink address number (1-255) for the RDD-DM4. This number must match the device number in your Axcess program. Use the PROlink DIP switch to set the PROlink address number for the RDD-DM4 (1-10). [. . . ] AMX reserves the right to alter specifications without notice at any time. 3000 research drive, richardson, TX 75082 USA · 469. 624. 8000 · 800. 222. 0193 · fax 469. 624. 7153 · technical support 800. 932. 6993 [. . . ]