User manual AOC 193FWK

[. . . ] The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibilities of the user to correct such interference. As an ENERGY STAR Partner our company has determined that this product meets the ENERGY STAR guidelines for energy efficiency. WARNING: To prevent fire or shock hazard, do not expose the monitor to rain or moisture. SAFETY: Lamp Disposal LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. FOR MORE INFORMATION, CONTACT THE 2 ELECTRONIC INDUSTRIES ALLIANCE AT WWW. EIAE. ORG. 3 PRECAUTIONS Do not use the monitor near water, e. g. [. . . ] If not, refer to the FAQ (frequently asked questions) section for troubleshooting. Caution: If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied). Connecting Cables Figure 2 1. DC-Jack Power Cable D-sub Cable AC Power Cord DVI Cable Connecting Cables 7 ADJUSTING THE VIEWING ANGLE For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference. Hold the stand so you do not topple the monitor when you change the monitor's angle. You are able to adjust the monitor's angle from -5 to 20. Figure 3 NOTES Do not touch the LCD screen when you change the angle. Careful attention is required not to catch your fingers or hands when you change the angle. 8 OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. The power indicator will light up. Figure 4 External Control Button EXTERNAL CONTROLS 1. Auto Adjust Key/Exit 9 FRONT PANEL CONTROL Power Button: Press this button to switch ON/OFF of monitor's power. Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON or Exit OSD menu when in Brightness/ Contrast Adjust OSD status. *Only adjustable at "STD" mode (see Brightness Preset below) MENU / ENTER : Luminance : Brightness Preset: Switch between "STD", "OFFICE" & "VIVID". Auto Adjust button / Exit: 1. 2. Power Indicator: When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu). When OSD menu is in off status, press this button over 2 seconds to activate the Auto Adjustment function. The Auto Adjustment function is used to set the HPos, VPos, Clock and Focus. Blue -- Power On mode. OSD Lock Function: To lock the OSD, press and hold the MENU button while the monitor is off and then press power button to turn the monitor on. To un-lock the OSD - press and hold the MENU button while the monitor is off and then press power button to turn the monitor on. NOTES Do not install the monitor in a location near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, or excessive dust or mechanical vibration or shock. Save the original shipping carton and packing materials, as they will come in handy if you ever have to ship your monitor. For maximum protection, repackage your monitor as it was originally packed at the factory. To keep the monitor looking new, periodically clean it with a soft cloth. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents such as thinner, benzene, or abrasive cleaners, since these will damage the cabinet. [. . . ] Check the signal-cable's connection pins for damage. INPUT NOT SUPPORT : Your computer has been set to unsuitable display mode , set the computer to display mode given in the following table. (see page 17) 16 APPENDIX SPECIFICATIONS Driving system TFT Color LCD Size 48cm(19") Pixel pitch Video Input 0. 285mm( H ) × 0. 285mm( V ) R, G, B Analog Interface Digital Interface Separate Sync. H/V TTL H-Frequency 30kHz ­83kHz V-Frequency Display Colors Dot Clock Max. Resolution Plug & Play EPA ENERGY STAR® Input Connector Input Video Signal ON Mode OFF Mode 55-75Hz 16. 2M Colors 135MHz 1440 × 900 @60Hz VESA DDC 2BTM 36W 1W LCD Panel 15-pin D-Sub DVI 24pin Analog:0. 7Vp-p(standard), 75 OHM, Positive Digital signal Horizontal : 410mm Vertical : 256mm 100~240VAC, 47~63Hz Operating Temp: 5° to 50°C Storage Temp. : -20° to 60°C Operating Humidity : 10% to 85% 440×356×215 (W ×H×D)mm 4kg Unit (net) Maximum Screen Size Power Source Environmental Considerations Dimension Weight (N. W. ) 17 Switch External Controls: Functions Power Consumption Regulatory Compliance ( Maximum ) Auto Adjust Key Brightness Preset Luminance Power Button MENU Contrast Brightness Focus Clock H. [. . . ]