User manual AOC 193P-

[. . . ] The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibilities of the user to correct such interference. 2. 3. WARNING: To prevent fire or shock hazard, do not expose the monitor to rain or moisture. SAFETY: Lamp Disposal LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. [. . . ] A certified power supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation H05VV-F 3G 0. 75mm2 or H05VVH2-F2 3G 0. 75mm2) shall be used. Alternative a flexible cord be of synthetic rubber according to IEC 60245 (designation H05RR-F 3G 0. 75mm2) shall be used. 5 CONTROLS AND CONNECTORS VIDEO CABLE Connecting the D-Sub Cable: Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer's D-Sub port. Connecting the Power Cord: Plug the AC-power cord into the External Adapter. Connecting the DVI Cable: Connect one end of the 24-pin DVI cable to the back of the monitor and connect the other end to the computer's DVI port. Caution: If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied). Figure 1 Connecting Cables 1. 4. Signal Cable DVI Cable 6 ADJUSTING THE VIEWING ANGLE · For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference. · Hold the stand so you do not topple the monitor when you change the monitor's angle. · You are able to adjust the monitor's angle from -5° to 25°. Figure 2 NOTES · Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. · Careful attention is required not to catch your fingers or hands when you change the angle. 7 OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (See Figure 3). By changing these settings, the picture can be adjusted to your personal preferences. The power indicator will light up. Figure 3 External Control Button EXTERNAL CONTROLS 1. Power Key 8 FRONT PANEL CONTROL · Power Button: Press this button to switch ON/OFF of monitor's power. · MENU / ENTER : Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON or Exit OSD menu when in Brightness/ Contrast Adjust OSD status. · Contrast : Adjust contrast or function adjust. · Brightness: Adjust brightness or function adjust. · Auto Adjust button / Exit: 1. When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu). When OSD menu is in off status, press this button over 2 seconds to activate the Auto Adjustment function. The Auto Adjustment function is used to set the HPos, VPos, Clock and Focus. · Power Indicator: Green -- Power On mode. OSD Lock Function: To lock the OSD, press and hold the MENU button while the monitor is off and then press power button to turn the monitor on. To un-lock the OSD - press and hold the MENU button while the monitor is off and then press power button to turn the monitor on. NOTES · Do not install the monitor in a location near heat sources such as radiators · · · or air ducts, or in a place subject to direct sunlight, or excessive dust or mechanical vibration or shock. Save the original shipping carton and packing materials, as they will come in handy if you ever have to ship your monitor. For maximum protection, repackage your monitor as it was originally packed at the factory. To keep the monitor looking new, periodically clean it with a soft cloth. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents such as thinner, benzene, or abrasive cleaners, since these will damage the cabinet. As a safety precaution, always unplug the monitor before cleaning it. 9 HOW TO ADJUST A SETTING 1. [. . . ] Check that the signal-cable is properly connected , If the connector is loose, tighten the connector's screws. Check the signal-cable's connection pins for damage. INPUT NOT SUPPORT : Your computer has been set to unsuitable display mode , set the computer to display mode given in the following table. (see page 18) 15 APPENDIX SPECIFICATIONS Driving system TFT Color LCD LCD Panel Size Pixel pitch Video Input 48cm(19") 0. 294mm( H ) × 0. 294mm( V ) R, G, B Analog Interface Digital Interface Separate Sync. Resolution Plug & Play Power Consumption Input Connector Input Video Signal ON Mode OFF Mode 30kHz ­ 83kHz 55-75Hz 16. 2M Colors 135MHz 1280 × 1024 @75Hz VESA DDC 2BTM 55W 2W 15-pin D-Sub DVI 24pin Analog:0. 7Vp-p(standard), 75 OHM, Positive Digital signal Horizontal : 376. 32mm Vertical : 301. 056mm 100~240VAC, 47~63Hz Operating Temp: 5° to 50°C Storage Temp. : -20° to 60°C Operating Humidity : 10% to 85% 406×415×246 (W ×H×D)mm 6. 0kg Unit (net) Maximum Screen Size Power Source Environmental Considerations Dimension Weight (N. W. ) 16 Switch External Controls: Functions Power Consumption Regulatory Compliance ( Maximum ) Auto Adjust Key Brightness Contrast Power Button MENU Contrast Brightness Focus Clock H. [. . . ]