User manual AOC 223VW

[. . . ] The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibilities of the user to correct such interference. WARNING: To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Refer servicing to qualified personnel only. 2 PRECAUTIONS Do not use the monitor near water, e. g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. [. . . ] Make sure that the power cord is the correct type required in your area. This LCD monitor has an External universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required. ) 3. Connect the AC-power cord into your LCD monitor's power input socket, The AC-power cord may be connected to either a wall power outlet or the power outlet socket on your PC, depending on the type of power cord supplied with your LCD monitor. CONTROLS AND CONNECTORS SIGNAL CABLE Connecting the Signal Cable: Plug the Signal Cable one end to LCD monitor's "DSUB-Input" socket, the other end to the computer's VGA port and tighten the two screws on the cable connector. Connecting the Power Cord: Plug the AC-power cord into the External Adapter. Connecting the DVI Cable: Connect one end of the 24-pin DVI cable to the back computer's DVI port. of the monitor and connect the other end to the 6 Figure 2 Connecting Cables 1. 3. Power input socket DVI input socket Signal input socket ADJUSTING THE VIEWING ANGLE · For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference. · Hold the stand so you do not topple the monitor when you change the monitor's angle. · You are able to adjust the monitor's angle from -5° to 20°. 7 Figure 3 NOTES · Do not touch the LCD screen when you change the angle. · Careful attention is required not to catch your fingers or hands when you change the angle. 8 OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located on the side of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. The power indicator will light up. Figure 4 External Control Button 9 EXTERNAL CONTROLS 1. Input Select Auto Adjust button / Exit Brightness Contrast MENU Power button LED FRONT PANEL CONTROL · Power Button: Press this button to switch ON/OFF of monitor's power. · MENU / ENTER : Active OSD menu or function adjust confirm or Exit OSD menu when in Contrast /Brightness OSD status. · Contrast : Adjust contrast or function adjust. · Brightness: · Power Indicator: Adjust brightness or function adjust. When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu). When OSD menu is in off status, press this button to activate the Auto Adjustment function. The Auto Adjustment function is used to optimized the HPos, VPos, Clock and Focus. OSD Lock Function: To lock the OSD, press and hold the MENU button while the monitor is off and then press power button to turn the monitor on. To un-lock the OSD - press and hold the MENU button while the monitor is off and then press power button to turn the monitor on. NOTES · Do not install the monitor in a location near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, or · · · excessive dust or mechanical vibration or shock. Save the original shipping carton and packing materials, as they will come in handy if you ever have to ship your monitor. For maximum protection, repackage your monitor as it was originally packed at the factory. To keep the monitor looking new, periodically clean it with a soft cloth. [. . . ] Check the signal-cable's connection pins for damage. INPUT NOT SUPPORT Your computer has been set to unsuitable display mode , set the computer to display mode given in the following table. APPENDIX SPECIFICATIONS Driving system TFT Color LCD LCD Panel Size Pixel Pitch Video 55. 8cm(22") 0. 282mm(H) × 0. 282mm(V) R, G, B Analog Interface Digital Interface 18 Input Separate Sync. H/V TTL H-Frequency V-Frequency 30kHz ­ 80kHz 55-75Hz 16. 7M Colors 165MHz 1680 x 1050@60Hz VESA DDC2BTM ON Mode OFF Mode 45W(max) 1W D-Sub 15pin DVI 24pin Analog:0. 7Vp-p(standard), 75 OHM, Positive Digital signal Horizontal : 473mm Vertical : 296mm 100~240VAC, 47~63Hz Operating Temp: 5° to 40° C Storage Temp. : -20° to 60° C Operating Humidity : 15% to 90% 5. 81kg Unit (net) 514. 4 (W) x 411. 7 (H) x 209. 4 (D)mm Display Colors Dot Clock Max. Resolution Plug & Play Power Consumption Input Connector Input Video Signal Maximum Screen Size Power Source Environmental Considerations Weight (N. W. ): Dimensions 19 Switch External Controls: Functions · · · · · · · · · · · · · · · · · · · · · Auto Adjust Button Brightness Contrast Power Button MENU Regulatory Compliance Contrast Brightness Focus Clock Input Select H. [. . . ]