User manual AOC 416V

[. . . ] Product Registration Please link www. aoc. com, select your country or region, log in Product Registration to register. FCC Notice FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] To ensure reliable operation of the monitor and to protect it from overheating, be sure these openings are not blocked or covered. Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided. The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Unplug the unit during a lightning storm or when it will not be used for long periods of time. Do not attempt to service the monitor yourself; opening or removing covers can expose you to dangerous voltages and other hazards. To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100 - 240V AC, Min. The wall socket shall be installed near the equipment and shall be easily accessible. For use only with the attached power adapter (Output 12Vdc) which have UL, CSA listed license(Only for monitors with power adapter). Setup the stand and base Please setup or remove the base following below steps. Adjusting Viewing Angle For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference. Hold the stand so you do not topple the monitor when you change the monitor's angle. You are able to adjust the monitor's angle from -5°to 15¡ã. NOTE: Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. Attaching the Cables Cable Connections On Back of Monitor and Computer 1. Power 2. Analog 3. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer's D-Sub port. Turn on your monitor and computer. If your monitor displays an image, installation is complete. If it does not display an image, see Troubleshooting. Attaching Wall Mounting Arm Preparing to Install An Optional Wall Mounting Arm This monitor can be attached to a wall mounting arm you purchase separately. Follow the manufacturer's instructions to assemble the wall mounting arm. Line up the holes of the arm with the holes in the back of the monitor. Refer to the user's manual that came with the optional wall mounting arm for instructions on attaching it to the wall. Noted : VESA mounting screw holes are not available for all models, please check with the dealer or official department of AOC. Setting the Optimal Resolution The recommended resolution for this monitor is 1920 by 1200. Set the resolution SLIDE-BAR to 1920 by 1200. External Controls Press the power button to turn the monitor on or off. [. . . ] "Picture Boost" is located in the fifth icon labeled "Picture Boost" in the OSD menu. Red Gain from Digital-register Yellow Gain from Digital-register Cyan Gain from Digital-register Magenta Gain from Digital-register Disable or Enable Full Enhance Mode Disable or Enable Nature Skin Mode Disable or Enable Green Field Mode Disable or Enable Sky-blue Mode Gamma DCR Image Setup Clock Focus H. Position V. Position Color Temp. Warm Normal Cool sRGB User User-B User-G User-R User-Y User-C User-M on or off on or off on or off on or off Color Boost Full Enhance Nature Skin Green Field Sky-blue AutoDetect Demo Picture Boost Frame Size Brightness Contrast Hue Saturation Position Bright Frame OSD Setup H. Position V. Position Timeout Language Extra Input Select Auto Config Reset DDC-CI Information on or off on or off 0-100 0-100 0-100 0-100 0-100 H. position V. position on or off 0-100 0-100 0-100 Disable or Enable AutoDetect Mode Disable or Enable Demo Adjust Frame Size Adjust Frame Brightness Adjust Frame Contrast Adjust Frame Hue Adjust Frame Saturation Adjust Frame horizontal Position Adjust Frame vertical Position Disable or Enable Bright Frame Adjust the verticalposition of OSD Adjust the horizontal position of OSD Adjust the OSD Timeout Select the OSD language Select Digital Sigal Source as Input Select Analog Sigal Source as Input Auto adjust the picture to default Reset the menu to default Turn ON/OFF DDC-CI Support Show the information of the main image and sub-image source Digital Analog yes or no yes or no LED Indicators Status Full Power Mode Active-off Mode LED Color Green Orange Specifications Model number Driving system Viewable image size Pixel pitch Video Separate Sync. [. . . ]