User manual AOC 619FH

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. [. . . ] You are able to adjust the monitor's angle from -5°to 20 °. NOTE: Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. Attaching the Cables Cable Connections On Back of Monitor and Computer 1. USB down x 4 Turn off your computer before performing the procedure below. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer's D-Sub port. (Optional ¨C Requires a video card with DVI port) - Connect one end of the 24-pin DVI cable to the back of the monitor and connect the other end to the computer¡¯s DVI port. (Optional ¨C Requires a video card with HDMI port) - Connect one end of the HDMI cable to the back of the monitor and connect the other end to the computer¡¯s HDMI port. Connect the audio cable to audio in port on the back of the monitor Turn on your monitor and computer. If your monitor displays an image, installation is complete. If it does not display an image, see Troubleshooting. Attaching Wall Mounting Arm Preparing to Install An Optional Wall Mounting Arm This monitor can be attached to a wall mounting arm you purchase separately. Follow the manufacturer's instructions to assemble the wall mounting arm. Line up the holes of the arm with the holes in the back of the monitor. Refer to the user's manual that came with the optional wall mounting arm for instructions on attaching it to the wall. Noted : VESA mounting screw holes are not available for all models, please check with the dealer or official department of AOC Setting the Optimal Resolution The recommended resolution for this monitor is 1920 by 1200. Set the resolution SLIDE-BAR to 1920 by 1200. External Controls Press the power button to turn the monitor on or off. The other control knobs are located at front panel of the monitor (See Figure ). By changing these settings, the picture can be adjusted to your personal preferences. The power indicator will light up. 1 Source 2 (Auto) / Exit 3 Eco mode / 4 Volume / + 5 Menu / Enter 6 Power Button & Indicator OSD Settings Press the MENU-button to activate the OSD window. Once the desired function is highlighted, press the MENU-buttonto activate it. If the function selected has a sub-menu, press s+ or - again to navigate through the sub-menu functions. Once the desired function is highlighted, press MENU-button to activate it. OSD Lock Function: To lock the OSD, press and hold the Menu button while the monitor is off and then press power button to turn the monitor on. To un-lock the OSD - press and hold the Menu button while the monitor is off and then press power button to turn the monitor on. Eco Mode hot key : Press the Eco key continuously to select the Eco mode of brightness when there is no OSD ( Eco mode hot key may not be available in all models). Volume adjustment hot key : When there is no OSD , press Volume (+) to active volume adjustment bar, press - or + to adjust volume ( Only for the models with speakers). Source hot key : When the OSD is closed, press Auto/Source button will be Source hot key function (Only for the models with dual or more inputs) . Press Source button continuously to select the input source showed in the message bar , press Menu/Enter button to change to the source selected. Auto configure hot key: When the OSD is closed, press Auto button will be auto configure hot key function . DCB Adjustment What is DCB? [. . . ] Display Color Dot Clock Horizontal scan range Horizontal scan Size(Maximum) Vertical scan range Vertical scan Size(Maximum) Optimal preset resolution Highest preset resolution Plug & Play Input Connector Input Video Signal Power Source Power Consumption Speakers Connector Type Signal Cable Type Dimensions & Weight: Height (with base) Width Depth Weight (monitor only) Weight (with packaging) Temperature: Operating Non-Operating Humidity: Operating Non-Operating Altitude: Operating Non-Operating 619Fh TFT Color LCD 649mm diagoanl 0. 2865mm(H) x 0. 2865mm(V) R, G, B Analog lnterface & Digital Interface, HDMI H/V TTL 16. 7M Colors 170 MHz 24 kHz - 83 kHz 550. 08mm 56 Hz - 76 Hz 343. 8mm 1920 x 1200 (60 Hz) 1920 x 1200 (60 Hz) VESA DDC2B/CI D-Sub 15pin & DVI-D, HDMI Analog: 0. 7Vp-p(standard), 75 OHM, Positive & DVI-D, HDMI 100~240VAC, 50/60Hz Active < 120 W Standby < 2 W 2 x 3W 15-pin Mini D-Sub & DVI-D, HDMI Detachable 472. 8 mm 605 mm 240 mm 7. 75kg 10. 8 kg 0° to 40° -20°to 60° 10% to 85% (non-condensing) 5% to 80% (non-condensing) 0~ 3000m (0~ 10000 ft ) 0~ 5000m (0~ 15000 ft ) Physical Characteristics Environmental EPA ENERGY STAR ® ENERGY STAR® is a U. S. As an ENERGY STAR® Partner, AOC International (Europe) GmbH has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. Preset Display Modes HORIZONTAL STAND VGA VGA VGA VGA Dos-mode SVGA SVGA SVGA SVGA Mac-mode XGA XGA XGA XGA VESA-Mode SXGA SXGA VESA-Mode VESA-Mode WSXGA WSXGA WUXGA SD SD SD SD SD SD RESOLUTION 640¡Á480 @60Hz DMT 640¡Á480 @67Hz MAC 640¡Á480 @72Hz DMT 640¡Á480 @75Hz DMT 720¡Á400 @70Hz DOS 800¡Á600 @56Hz DMT 800¡Á600 @60Hz DMT 800¡Á600 @72Hz DMT 800¡Á600 @75Hz DMT 832¡Á624 @75Hz MAC 1024¡Á768 @60HzDMT 1024¡Á768 @70Hz DMT 1024¡Á768 @75Hz DMT 1024¡Á768 @75Hz MAC 1280¡Á960 @60Hz DMT 1280¡Á1024 @60Hz DMT 1280¡Á1024 @75Hz DMT 1440¡Á900 @60Hz CVT16:10 1440¡Á900 @60Hz CVT16:10 R 1680¡Á1050 @60Hz CVT16:9 1680¡Á1050 @60Hz CVT16:9 R 1920x1200@60Hz 480P for HDTV Digital only 480I for HDTV Digital only 720I for HDTV Digital only 720P for HDTV Digital only 576I for HDTV Digital only 576P for HDTV Digital only 1080I for HDTV Digital only 1080P for HDTV Digital only FREQUENCY(kHz) 31. 469 35. 000 37. 861 37. 500 31. 469 35. 156 37. 879 48. 077 46. 875 49. 725 48. 363 56. 476 60. 023 60. 241 60. 000 63. 981 79. 976 55. 935 55. 469 65. 290 64. 674 74. 038 31. 500 15. 750 37. 500 45. 000 31. 250 31. 250 33. 750 60. 50 VERTICAL FREQUENCY(Hz) 59. 940 66. 667 72. 809 75. 000 70. 087 56. 250 60. 317 72. 188 75. 000 74. 500 60. 004 70. 069 75. 029 74. 927 60. 000 60. 020 75. 025 59. 887 59. 901 59. 954 59. 883 59. 950 60. 000 60. 000 50. 000 60. 000 50. 000 50. 000 60. 000 60. 000 Pin Assignments Pin Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 15-Pin Side of the Signal Cable Video-Red Video-Green Video-Blue N. C. 1 2 3 4 5 6 7 8 Signal Name TMDS Data 2TMDS Data 2+ TMDS Data 2/4 Shield TMDS Data 4TMDS Data 4+ DDC Clock DDC Data N. C. Pin No. 9 10 11 12 13 14 15 16 Signal Name TMDS Data 1TMDS Data 1+ TMDS Data 1/3 Shield TMDS Data 3TMDS Data 3+ +5V Power Ground(for+5V) Hot Plug Detect Pin No. [. . . ]