User manual AOC L22H998

[. . . ] 22" LCD TV L22H998 Content FOR YOUR SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 PRECAUTIONS AND REMINDERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Quick Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The TV should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. Unplug this apparatus during lightning storms or when unused for long periods of time. See Figure below. EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE Note to the CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. Please, make sure to connect the power plug to the wall outlet socket after connecting the TV to the adapter!Objects and Liquid Entry ­ Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings. 7 Quick Installation Install Remove Install the stand base to the TV. Remove the stand base from the TV. 8 Wall-mount instruction Preparing To Install The Optional Wall Mount Arm (not included) This TV can be attached to a wall mounting arm you can purchase separately. Turn the power OFF then disconnect the cables from the TV before performing the procedure below. Remove the hinge cover. 3. Remove the 4 screws holding the stand to the hinge. 4. Remove the stand. 9 Attaching The Optional Wall Mount Arm (not supplied) Follow these steps to finish installing the wall mounting arm: 1. Line up the holes of the arm with the holes in the back of the monitor. Refer to the user's manual that came with the optional wall mounting arm for instructions on attaching it to the wall. NOTE 100mmx100mm VESA high hole (n=4), M4, pitch =0. 7 mm screw mounting kit not included. Due to safety concerns, if the VESA mounting kit is purchased separately please make sure the mounting kit is UL-Listed, and replaceable only by service personnel. 10 ACCESSORIES Thank you for purchasing this LCD-TV. This LCD-TV package comes with: LCD TV User's Guide book Remote control Battery AA x 2 Power Cord Quick Setup Guide Pedestal stand 11 FRONT PANEL BUTTONS Volume Up Volume Down On Screen Display Menu On/Off CH Up CH Down Input Source Selection (Enter) Power ON/OFF button Power LED Indicator Remote Control Receiver 12 BACK PANEL BUTTONS AB A B C D E F G H I J K L C DE FG H I J K L AC Power Switch (Must be turned on) Power (AC input) HDMI Input Terminal VGA signal input Composite Video input YPbPr signal input S-Video input AV/ S-Video signal Audio input (left/right) YPbPr signal Audio input (left/right) PC Audio input Headphone Jack Cable/ Air TV input 13 REMOTE CONTROL 14 Remote control button function as follows: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 INPUT ENTER TV - VOL + LIST GUIDE 0~9, - number POWER UP/ DOWN/ LEFT/ RIGHT MENU CH Input source select Confirm selection or enter selected menu Direct to TV source Adjust volume UP/DOWN Select channel from program list Select electronic program guide (EPG) (Only available in DTV source) Directly channel select Power ON/OFF Move the cursor In OSD menu: UP/ DOWN for OSD function select and LEFT/ RIGHT for function adjust On Screen Display (OSD) menu ON/OFF Adjust channel UP/DOWN Select from preset Favorite Channels Adjust window size Volume mute ON/OFF Display current information Set timer to turn off TV Select Mono, Stereo or SAP sound Select caption mode Return to previous channel FAV ZOOM MUTE INFO SLEEP MTS C. C LAST 15 INSTALLATION Connecting RF antenna and Cable TV Make sure the power is OFF before installing your LCD TV. 1) AIR TV: Connect the LCD TV to TV antenna with 75-ohm coaxial cable. Preset the air TV channels into memory with Auto Scan function when using an antenna TV system. Besides, the TV system (NTSC) and DTV system (ATSC) can be found by the scanning of "AIR" with Auto Scan function. 2) Cable TV: Connect the LCD TV to the cable with CATV and Digital cable. Preset the cable TV channels into memory with Auto Scan function when using a cable TV system. Besides, the CATV system (cable TV) and Digital cable system (clear QAM) can be found by the scanning of "Cable" with Auto Scan function. See page 33. RF Cable, CATV/ Digital cable or Adapter (not supplied) Note: Users can select either Air or Cable TV cable to be connected to the TV IN jack. To watch both of them, use an adapter to connect both Air and Cable cables to the jack. Connecting to DVD / Set Top Box Connect Video/Audio cables from compatible devices into the back panel of LCD TV. 1) With AV cable: VCD or DVD Player RCA A/V Cable (not supplied) 16 2) With S-Video cable: S-Video Cable (not supplied) VCD or DVD Player Audio Cable (not supplied) 3) With YPbPr cable: YPbPr Cable (not supplied) VCD or DVD Player Audio Cable (not supplied) 4) With HDMI cable: VCD or DVD Player (DVD Player should have the HDMI output terminal) HDMI Cable (not supplied) 17 5) With HDMI-DVI cable: Audio Cable (not supplied) VCD or DVD Player (DVD Player should have the HDMI output terminal) HDMI-DVI Cable (not supplied) Connecting to the Headphone Connect the headphone to the headphone output terminal of the LCD TV. (Headphone sold separately). Headphone (not supplied) Connecting to a Computer 1) With VGA Cable: Connect the VGA cable from VGA output of the computer to the VGA terminal input of your LCD TV. [. . . ] Reset RRT: Press to reset RRT Setting. 32 CHANNEL Menu --To set up for TV Note: The Channel Menu is only active in TV source. When in AV, S-Video, YPbPr, HDMI, or PC source, the CHANNEL Menu will not appear. Note: The condition of DTV Signal will only be displayed when source is in DTV. Select Air or Cable in TV option, and press to start auto scanning TV channels. Press MENU again at any time to interrupt scanning. 33 Favorite: To set your favorite channels into memory. [. . . ]