User manual AOC LM540

[. . . ] The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. Warning To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Refer servicing to qualified personnel only. LM540 2 17NOV04 For Your Safety Precautions · Do not use the monitor near water, e. g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. [. . . ] Be sure to repackage your monitor as it was originally packed at the factory. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents such as thinners, benzene, or abrasive cleaners, since these will damage the cabinet. Always unplug the monitor before cleaning it. Using the Right Power Cord The supplied power cord is a NEMA 5-15 style plug. If the monitor will be connected to your computer's power outlet, use a minimum No. 18 AWG, type SJT or SVT three conductors cord with one end terminating with a male grounded plug, rated 10A, 250V, CEE-22. The other end must terminate with a molded-on type connector body, rated 10A, 250V, having standard CEE-22 female configuration. 4 17NOV04 LM540 Before You Operate the Monitor Installing & Removing the Base LM540 General Features: · 38. 1cm(15") TFT Color LCD Monitor · Crisp, Clear Display for Windows · Supports Resolutions up to 1024 X 768 pixels @75Hz, (1024 x 768 @ 60Hz Recommended) · EPA ENERGY STAR® · Ergonomic Design · Space Saving, Compact Case Design LM540 Package Contents The box that your monitor was shipped in should have included the following items: 1. Booklet (Containing Warranty & Safety Information) 5 17NOV04 Before You Operate the Monitor Connecting the Wires Using the Power Cord Supplied LM540 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws. Plug the other end of the power cord into a grounded AC outlet or UL-approved power strip. Caution: Make sure the power cord is the correct type that is required in your area. This LCD monitor has a universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage areas (no user adjustment is required). If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied). LM540 6 17NOV04 Before You Operate the Monitor Adjusting the Viewing Angle LM540 For optimal viewing, adjust the monitor's angle to your own preference. · Hold the stand firmly when you change the monitor's angle. · You can adjust the monitor's angle from -5° to 25°. · Do not touch the LCD screen when you change the angle. · Be careful to avoid pinching your hand in the swivel base. LM540 7 17NOV04 Before You Operate the Monitor LM540 Preparing To Install An Optional Wall Mounting Arm (Not Supplied) This monitor can be attached to a wall mounting arm you can purchase separately. Follow the manufacturer's instructions to assemble the wall mounting arm. See next page for further installation instructions. LM540 8 17NOV04 Before You Operate the Monitor nstall An Optional Wall Mounting Arm (Not Supplied) LM540 Follow these steps to finish installing the wall mounting arm: 1. Line up the holes of the arm with the holes in the back of the monitor. NOTE: The Envision LM540 is compatible with the Ergotron line of mounting and arm solutions. [. . . ] If the frequency is not correct, the screen shows vertical stripes and the picture's width is incorrect. With a wrong phase adjustment the picture has horizontal disturbances with very light screen images. Note: For FOCUS and CLOCK adjustment use "dot-pattern" or Win 95/98 shut-down mode pattern. Error Message Cable not connected Possible Solution · Make sure the video cable is properly connected to the computer. · Inspect the video cable and make sure that none of the pins are bent. LM540 14 17NOV04 Technical Support (FAQ) Error Message Input not supported LM540 Possible Solution · Your computer has been set to an incompatible display mode. Click the Settings tab then set your computer's display mode to one of the settings listed in the resolution chart below. [. . . ]