User manual ASUS AP140R-E1

[. . . ] AP140R-E1 Intel® Pentium® 4 1U Rackmount Server 800/533MHz Front Side Bus User Guide E1656 Revised edition V2 August 2004 Copyright © 2004 ASUSTeK COMPUTER INC. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. ASUS provides this manual "as is" without warranty of any kind, either express or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no event shall ASUS, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of use or data, interruption of business and the like), even if ASUS has been advised of the possibility of such damages arising from any defect or error in this manual or product. [. . . ] Floppy disk drive connector (34-1 pin FLOPPY1) SMBus connector (6-1 pin BPSMB1) IDE connectors (40-1 pin PRI_IDE [blue], SEC_IDE [black]) Serial ATA connectors (7-pin SATA1, SATA2) ATX power connectors (20-pin, 4-pin) LED connector (2-pin J3) Fan connectors (3-pin FAN1/2/3/4/5/6) Chassis intrusion connector (4-1 pin CHASSIS1) USB header (10-1 pin USB34) System panel connector (20-1 pin PANEL1) - LAN connection indicators (2-pin LAN1_LED, LAN2_LED) - Hard disk activity LED (2-pin IDE_LED) - Front panel location LED (2-pin FP_LOCLED) - System power LED (2-pin PWR_LED) - Reset switch (2-pin RESET) - ATX power button/ Soft-off switch (2-pin PWRBTN) - Message LED (2-pin MSG_LED) - Front panel location switch (2-pin FP_LOCSW) 4-8 4-8 4-9 4-10 4-11 4-11 4-12 4-12 4-13 4-13 4-14 4-14 4-14 4-14 4-14 4-14 4-14 4-14 ASUS AP140R-E1 1U barebone server 4-3 4. 2 Jumpers 1. Keyboard power (3-pin KBPWR1) This jumper allows you to enable or disable the keyboard wake-up feature. Set this jumper to pins 2-3 (+5VSB) if you wish to wake up the computer when you press a key on the keyboard (the default is the Space Bar). This feature requires an ATX power supply that can supply at least 1A on the +5VSB lead, and a corresponding setting in the BIOS (see section 4. 5. 1 Power Up Control). KBPWR1 12 No KB Wake-Up (Default) 23 KB Wake-Up ® PSCH-LR PSCH-LR Keyboard Power Setting 2. Gigabit LAN1 controller setting (3-pin LAN_EN1) This jumper allows you to enable or disable the Intel® 82541GI Gigabit LAN controller. Setting this jumper to pins 2-3 disables the Gigabit LAN port (RJ-45) on the rear panel that corresponds to this controller. ® LAN_EN1 12 Enable (Default) 23 Disable PSCH-LR PSCH-LR LAN_EN1 Setting 4-4 Chapter 4: Motherboard information 3. Gigabit LAN2 controller setting (3-pin LAN_EN2) This jumper allows you to enable or disable the Intel® 82547GI Gigabit LAN controller. Setting this jumper to pins 2-3 disables the Gigabit LAN port (RJ-45) on the rear panel that corresponds to this controller. LAN_EN2 ® 12 Enable (Default) 23 Disable PSCH-LR PSCH-LR LAN_EN2 Setting 4. Onboard VGA setting (3-pin VGA_EN1) This jumper allows you to enable or disable the onboard VGA. Set this jumper to disabled (pins 2-3) if you wish to install a VGA card. VGA_EN1 12 ® 23 Disable Enable (Default) PSCH-LR PSCH-LR VGA Jumper Setting ASUS AP140R-E1 1U barebone server 4-5 5. Recovery setting (3-pin RECOVERY1) This jumper allows you to update/recover the BIOS quickly. Prepare a floppy disk that contains the latest BIOS for the motherboard (xxxx-xxx. BIN) and the AWDFLASH. EXE utility. Turn on the system. RECOVERY1 12 ® 23 Recovery Normal (Default) PSCH-LR PSCH-LR RECOVERY Setting 4-6 Chapter 4: Motherboard information 6. Clear RTC RAM (3-pin CLRTC1) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The RAM data in CMOS, that include system setup information such as system passwords, is powered by the onboard button cell battery. Keep the cap on pins 2-3 for about 5~10 seconds, then move the cap back to pins 1-2. Hold down the <Del> key during the boot process and enter BIOS setup to re-enter data. CLRTC1 ® 2 1 Normal (Default) PSCH-LR 3 2 Clear CMOS PSCH-LR Clear RTC RAM Except when clearing the RTC RAM, never remove the cap on CLRTC jumper default position. Removing the cap will cause system boot failure! ASUS AP140R-E1 1U barebone server 4-7 4. 3 Connectors This section describes the internal connectors on the motherboard. Refer to section "1. 4 Rear panel features" for information on the external (rear panel) connectors. 1. Floppy disk drive connector (34-1 pin FLOPPY1) This connector supports the provided floppy drive ribbon cable. After connecting one end to the motherboard, connect the other end to the floppy drive. [. . . ] When prompted, confirm the password by typing the exact characters again, then press <Enter>. A note about passwords The Supervisor password is required to enter the BIOS Setup program preventing unauthorized access. The User password is required to boot the system preventing unauthorized use. If you forget your password, you can clear it by erasing the CMOS Real Time Clock (RTC) RAM. [. . . ]