User manual ASUS CUV4X-CME

[. . . ] (Bottom) 15 USB Connectors (Port 0 & Port 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 USB Connectors (Port 2 & Port 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1 PS/2 Mouse Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (Top) 17 1 PS/2 Keyboard Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Pin 1 is usually on the side closest to the power connector on hard drives and CD-ROM drives, but may be on the opposite side on floppy disk drives. 1) Primary (Blue) / Secondary IDE Connectors (40-1 pin IDE1/IDE2) These connectors support the provided UltraDMA/66 IDE hard disk ribbon cable. Connect the cable's blue connector to the primary (recommended) or secondary IDE connector, then connect the gray connector to the UltraDMA/66 slave device (hard disk drive) and the black connector to the UltraDMA/66 master device. It is recommended that non-UltraDMA/66 devices be connected to the secondary IDE connector. If you install two hard disks, you must configure the second drive to Slave mode by setting its jumper accordingly. Refer to the hard disk documentation for the jumper settings. Secondary IDE Connector Primary IDE Connector NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1. CUV4X-CME CUV4X-CME IDE Connectors PIN 1 ASUS CUV4X-CME User's Manual 7 H/W SETUP Connectors HARDWARE SETUP 2) Floppy Disk Drive Connector (34-1 pin FLOPPY) This connector supports the provided floppy drive ribbon cable. After connecting the single end to the board, connect the two plugs on the other end to the floppy drives. CUV4X-CME CUV4X-CME ATX Power Connector 8 ASUS CUV4X-CME User's Manual +12. 0 Volts +5V Standby Power Good Ground +5. 0 Volts Ground +5. 0 Volts Ground +3. 3 Volts +3. 3 Volts +5. 0 Volts +5. 0 Volts -5. 0 Volts Ground Ground Ground Power Supply On Ground -12. 0 Volts +3. 3 Volts H/W SETUP Connectors CUV4X-CME NOTE: Orient the red markings on the floppy ribbon cable to PIN 1 PIN 1 CUV4X-CME Floppy Disk Drive Connector 3) ATX Power Supply Connector (20-pin block ATXPWR) This connector connects to an ATX power supply. The plug from the power supply fits in only one orientation because of the different hole sizes. Find the proper orientation and push down firmly making sure that the pins are aligned. HARDWARE SETUP 4) CPU Fan Connector (3-pin CPU_FAN) The CPU fan connector supports cooling fans of 350mA (4. 2 Watts) or less. Connect the fan plug to the board taking into consideration the polarity of the connector. GND +12V NC CPU_FAN CUV4X-CME CUV4X-CME 12-Volt Cooling Fan Power 5) USB Header (10-1 pin USBPORT) (optional) If the USB port connectors on the back panel are inadequate, one USB header is available for two additional USB port connectors. Connect the USB header to a 2-port USB connector set and mount the bracket to an open slot on the chassis. (NOTE: The USB connector set does not come with the motherboard package. ) USBPORT GND GND P2+ P2USB PWR 1 6 USB PWR P3P3+ GND GND 5 10 CUV4X-CME CUV4X-CME Front Panel USB Header ASUS CUV4X-CME User's Manual 9 H/W SETUP Connectors HARDWARE SETUP 6) Standard Infrared Module Connector (5-pin IR) This connector supports an optional wireless transmitting and receiving infrared module. The infrared module mounts to a small opening on system cases that support this feature. Use the five pins as shown in Back View and connect a ribbon cable from the module to the motherboard SIR connector according to the pin definitions. H/W SETUP Connectors CUV4X-CME CUV4X-CME IR +5V (NC) IRRX GND IRTX Front View Back View 1 IRTX GND IRRX +5V (NC) CUV4X-CME Infrared Module Connector 7) Internal Audio Connectors (4-pin CD_IN, AUX, VIDEO, MODEM) These connectors allow you to receive stereo audio input from sound sources as a CD-ROM, TV tuner, or MPEG card. The MODEM connector allows the onboard audio to interface with a voice modem card with a similar connector. It also allows the sharing of mono_in (such as a phone) and a mono_out (such as a speaker) between the audio and a voice modem card. CD (White) Left Audio Channel Ground Right Audio Channel AUX (Black) Left Audio Channel Ground Right Audio Channel MODEM Modem-In (to Modem) Ground Modem-Out (from Modem) CUV4X-CME Internal Audio Connectors 10 ASUS CUV4X-CME User's Manual HARDWARE SETUP The following PANEL illustration is for items 8-11. Power LED HD LED +PLED -PLED +HDLED -HDLED PWR Ground Reset Ground ATX Power Switch* Reset SW * Requires an ATX power supply. CUV4X-CME CUV4X-CME System Panel Connectors 8) System Power LED Connector(2-pin PWRLED) This 3-1 pin connector connects to the system power LED. The LED lights up when you turn on the system power, and blinks when the system is in sleep or soft-off mode. 9) Hard Disk LED Connector (2-pin HDLED) This 2-pin connector is for the hard disk LED. 10) ATX Power Switch Connector (2-pin PWR) The system power is controlled by a momentary switch attached to this connector. 11) Reset Switch Connector (2-pin RESET) This 2-pin connector connects to the case-mounted reset switch for rebooting the system without turning off the power switch. This is a preferred method ASUS CUV4X-CME User's Manual 11 H/W SETUP Connectors HARDWARE SETUP Starting Up the First Time 1. [. . . ] ASUS CUV4X-CME User's Manual HARDWARE SETUP Managing and Updating Your BIOS Upon First Use of the Computer System It is recommended that you save a copy of the original motherboard BIOS along with a Flash Memory Writer utility (AFLASH. EXE) to a bootable floppy disk in case you need to reinstall the BIOS later. Type the filename of your new BIOS and the path, for example, A:\XXXXX. XXX, then press <Enter>. When prompted to confirm the BIOS update, press Y to start the update. ASUS CUV4X-CME User's Manual 15 BIOSSETUP H/W SETUP Updating BIOS Connectors HARDWARE SETUP 7. The utility starts to program the new BIOS information into the Flash ROM. [. . . ]