User manual ASUS K8S-MX

[. . . ] K8S-MX User Guide Motherboard E1884 Checklist Revised Edition V2 December 2004 Copyright © 2004 ASUSTeK COMPUTER INC. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. [. . . ] Make sure that the floppy disk has at least 600KB of free disk space and is not writeprotected. A:\>afudos /oMYBIOS03. ROM AMI Firmware Update Utility - Version 1. 10 Copyright (C) 2002 American Megatrends, Inc. done A:\> When the copy process is complete, the utility returns to the DOS prompt. 2. 1. 4 Using ASUS EZ Flash to update the BIOS The ASUS EZ Flash feature allows you to easily update the BIOS without having to go through the long process of booting from a diskette and using a DOS-based utility. The EZ Flash is built-in the BIOS firmware so it is accessible by simply pressing <Alt + F2> during the Power-On Self Tests (POST). To update the BIOS using ASUS EZ Flash: 1. Visit the ASUS website (www. asus. com) to download the latest BIOS file for your motherboard and rename the downloaded file as K8S-MX. ROM. To launch EZ Flash, press <Alt+F2> during POST to display the following. User recovery requested. Checking for floppy. . . · · If there is no floppy disk in the drive, the error message "Floppy not found!" appears. If the correct BIOS file is not in the floppy disk, the error message "Floppy not found!" is displayed. Make sure to rename the downloaded BIOS file as "K8S-MX. ROM". 4. If all the necessary files are found in the floppy disk, EZ Flash performs the BIOS update process and automatically reboots the system when done. ASUS K8S-MX motherboard 2-5 DO NOT shutdown or reset the system while updating the BIOS!Rebooting. 2. 1. 5 Recovering the BIOS with CrashFree BIOS 2 The CrashFree BIOS 2 auto recovery tool allows you to restore BIOS from the motherboard support CD, or from a floppy disk that contains the BIOS file, in case the current BIOS on the motherboard fails or gets corrupted. · Prepare the support CD that came with the motherboard or a floppy disk that contains the motherboard BIOS before proceeding with the BIOS update process. If you have saved a copy of the original motherboard BIOS to a bootable floppy disk, you may also use this disk to restore the BIOS. See section "2. 1. 1 Creating a bootable floppy disk. " · To recover the BIOS from a floppy disk: 1. When a corrupted BIOS is detected, the following screen message appears. Bad BIOS checksum. Insert a floppy disk that contains the original or the latest BIOS file for this motherboard. If all the necessary files are found in the floppy disk, the BIOS update process continues. Make sure that the BIOS file in the floppy disk is renamed as "K8S-MX. ROM". 2-6 Chapter 2: BIOS Setup Bad BIOS checksum. Start flashing. . . DO NOT shut down or reset the system while updating the BIOS!When the BIOS update process is complete, reboot the system. To recover the BIOS from the support CD: 1. When a corrupted BIOS is detected, the following screen message appears. Bad BIOS checksum. Checking for floppy. . . If there is no floppy disk found in the drive, the system automatically checks the CD-ROM. 3. The support CD contains the a working BIOS for this motherboard. Bad BIOS checksum. Start flashing. . . DO NOT shut down or reset the system while updating the BIOS!When the BIOS update process is complete, reboot the system. The recovered BIOS may not be the latest BIOS version for this motherboard. [. . . ] From the RAID Setup, press <2> then <Enter> to select RAID 0 (Striping). 2. Select <1> to auto-create a RAID array or press <2> to manually configure array then press <Enter>. 3. If you selected 2, select the array block size by pressing the corresponding number beside the available block sizes then press <Enter>. 3-10 Chapter 3: Software support 5. Use the up/down arrow keys to move the selection bar, then press <Enter> to select a disk drive. 6. [. . . ]